Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/o Memory)
RM37A0E _59 Vehicle Exterior _086891 MIRROR (EXT) _0420034 POWER MIRROR CONTROL SYSTEM(w/o Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/o Memory)  AUTO Power Retract Mirrors do not operate  


DESCRIPTION

The outer mirror switch assembly sends a mirror auto retract/return signal to the main body ECU (multiplex network body ECU) when the retractable outer mirror switch on the outer mirror switch assembly is in the AUTO position. The main body ECU (multiplex network body ECU) retracts or returns the outer rear view mirror assemblies based on the lock/unlock signal of each door while the ignition switch is off.

WIRING DIAGRAM

B508287E09
2.302,0.573 2.76,0.771 0.458,0.198 10 false MAT 4.563,0.573 5.021,0.771 0.458,0.198 10 false AMR 2.719,0.469 2.875,0.667 0.156,0.198 10 false 9 4.354,0.469 4.51,0.667 0.156,0.198 10 false 6 0.896,1.073 1.938,1.281 1.042,0.208 10 false J22 0.885,1.219 5.167,1.417 4.281,0.198 10 false Outer Mirror Switch Assembly 4.313,1.073 4.771,1.271 0.458,0.198 10 false H44 4.594,1.083 6.25,1.49 1.656,0.406 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK POWER RETRACT MIRROR FUNCTION
a.

Check the power retract mirror function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Power retract mirror function operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Retractable Mirrors do not Operate with Power Retract Mirror Switch)

2.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check the power door lock control system.

for Sedan: Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

for Hatchback: Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Power door lock control system is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

NG

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock control system.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Wireless door lock control system is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK ENTRY AND START SYSTEM (for Entry Function)

NG

4.CHECK ENTRY AND START SYSTEM (for Entry Function)
a.

Check the entry and start system (for Entry Function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

OK:

Entry and start system (for Entry Function) is normal.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS

NG

5.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto Mirror SW Retractable outer mirror switch signal OFF or ON OFF: Retractable outer mirror switch not in auto position
ON: Retractable outer mirror switch in auto position
-
Body Electrical > Main Body > Data List
Tester Display
Auto Mirror SW
50003 123 105
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT OUTER MIRROR SWITCH ASSEMBLY
6.INSPECT OUTER MIRROR SWITCH ASSEMBLY

OK

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H44 main body ECU (multiplex network body ECU).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J22-9 (MAT) - H44-6 (AMR) Always Below 1 Ω
J22-9 (MAT) or H44-6 (AMR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR