Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086851 2GR-FKS ENGINE MECHANICAL _0420080 ENGINE G

2GR-FKS ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A345137

To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fans when working in the engine compartment with the engine running or the ignition switch ON.


PROCEDURE

Hide 17801 5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that the air cleaner filter element sub-assembly is not damaged or excessively oily.

HINT:
·

If there is any dirt or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




c.

Install the air cleaner filter element sub-assembly.


Hide 16620 7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

a.

Remove the V-ribbed belt.

Click hereGeneral>MAINTENANCE>2GR-FKS DRIVE BELT>REMOVAL


b.

Turn the V-ribbed belt tensioner assembly clockwise and counterclockwise and check that it turns smoothly and does not catch.

HINT:

If the V-ribbed belt tensioner assembly does not turn smoothly or catches, replace the V-ribbed belt tensioner assembly.



c.

Install the V-ribbed belt.

Click hereGeneral>MAINTENANCE>2GR-FKS DRIVE BELT>INSTALLATION


Hide 13750 8.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.


b.

If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.

HINT:

If any defects or problems are found during the inspection, perform valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION



Hide 9.INSPECT IGNITION TIMING

NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.



a.

Start the engine and warm it up.


b.

Monitor Ignition Timing Cylinder #1 of the Data List.

Powertrain > Engine > Data List
Tester Display
Ignition Timing Cylinder #1
50003 372 213
Standard Ignition Timing:

12 to 24° BTDC at idle



c.

Check that the ignition timing advances immediately when the engine speed is increased.


d.

Monitor Ignition Timing Cylinder #1 of the Data List.

Powertrain > Engine > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Ignition Timing Cylinder #1
50004 372 22 213
Standard Ignition Timing:

8 to 12° BTDC at idle



Hide 10.INSPECT ENGINE IDLE SPEED

NOTICE:
·

Check the idle speed with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the idle speed, the transaxle should be in neutral or park.



a.

Start the engine and warm it up.


b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211
Standard Idle Speed:

650 to 750 rpm



Hide 11.INSPECT COMPRESSION

NOTICE:

Keep the intake manifold and spark plug holes free of foreign matter when measuring the compression pressure.


a.

Warm up and stop the engine.




d.
A455092

Disconnect the 2 No. 5 engine wire connectors (for Port Injection).

NOTICE:

Perform this step in order to stop fuel injection to prevent damage to the catalyst due to unburned fuel.



e.
A455093

Disconnect the No. 6 engine wire connector and No. 7 engine wire connector (for Direct Injection).

NOTICE:

Perform this step in order to stop fuel injection to prevent damage to the catalyst due to unburned fuel.



f.
A455094

Check the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

While cranking the engine, measure the compression pressure.

Standard Compression Pressure:

1400 kPa (14.3 kgf/cm2, 203 psi)


Minimum Compression Pressure:

1050 kPa (10.7 kgf/cm2, 152 psi)


Pressure Difference between Each Cylinder:

200 kPa (2.0 kgf/cm2, 29 psi) or less


NOTICE:
·

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.

·

Inspect all cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




iii.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole then inspect the cylinder compression pressure again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.





g.

Connect the No. 6 engine wire connector and No. 7 engine wire connector (for Direct Injection).


h.

Connect the 2 No. 5 engine wire connectors (for Port Injection).



j.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

After performing the inspection, clear the DTCs and confirm that DTCs are not stored again or that the normal system code is output if using a check wire.



Hide 12.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Run the engine speed at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.


d.

Immediately check the CO/HC concentration at idle and then at an engine speed of 2500 rpm.

HINT:

When performing a 2 mode test (with the engine idling/running at 2500 rpm), the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Cause
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect valve timing

-

Fouled, shorted or improperly gapped spark plugs


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders


Low High Rough idle
(Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle body with motor assembly

-

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty SFI system:

-

Fuel pressure regulator assembly

-

Engine coolant temperature sensor

-

Mass air flow meter sub-assembly

-

ECM

-

Fuel injector assemblies

-

Throttle position sensor (built into throttle body with motor assembly)