Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086851 2GR-FKS ENGINE MECHANICAL _0420085 REAR CRANKSHAFT OIL SEAL A

2GR-FKS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11381A 1.INSTALL REAR ENGINE OIL SEAL

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A369438C01
1.01,2.635 1.292,2.635 true 2.052,1.281 2.906,1.969 2.906,1.969 2.063,0.771 true 2.563,2.656 2.906,1.979 true 0.854,2.563 1.167,2.719 0.313,0.156 10 false *1 1.552,1.979 1.865,2.135 0.313,0.156 10 false *a 2.969,1.896 3.427,2.094 0.458,0.198 10 false SST
*1 Rear Engine Oil Seal Retainer
*a Oil Seal Protrusion Height


Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap in the rear engine oil seal at an angle.




c.

Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-15030  
09950-70010  (09951-07150)

Oil Seal Protrusion Height:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Do not tap in the rear engine oil seal at an angle.



Hide 19315 2.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A369439

Install the No. 1 crankshaft position sensor plate.

HINT:

Align the pin of the No. 1 crankshaft position sensor plate with the pin hole of the crankshaft.



Hide 32101 3.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A369435N01
1.25,1.052 0.635,1.5 0.635,1.5 1.708,1.292 true 0.323,1.531 0.781,1.729 0.458,0.198 10 true SST

Using SST, hold the crankshaft pulley.

SST
09213-70011  (09213-70020)
09330-00021  


b.

Clean the 8 bolts and 8 bolt holes.


c.
A369440C01
1.438,0.24 2.01,0.24 false 2.5,3.323 3.073,3.323 false 2.073,0.167 2.385,0.323 0.313,0.156 10 false *1 3.125,3.25 3.375,3.552 0.25,0.302 10 false *2
*1 Drive Plate and Ring Gear Sub-assembly
*2 Rear Drive Plate Spacer
V100135

Transaxle Side


Install the drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.


d.
A369441C01
1.979,1.156 2.177,0.365 2.177,0.365 2.469,0.365 false 2.521,0.292 2.833,0.448 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
A369436N01
2.323,0.771 2.479,0.969 0.156,0.198 10 true 7 2.021,0.292 2.177,0.49 0.156,0.198 10 true 1 2.281,1.24 2.438,1.438 0.156,0.198 10 true 4 1.896,1.531 2.052,1.729 0.156,0.198 10 true 6 1.396,1.49 1.552,1.688 0.156,0.198 10 true 2 1.01,1.031 1.167,1.229 0.156,0.198 10 true 8 1.042,0.552 1.198,0.75 0.156,0.198 10 true 3 1.51,0.208 1.667,0.406 0.156,0.198 10 true 5

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.