Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › 2020.02–2020.11
RM37A0E _52 Drivetrain _086859 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0418484 AUTOMATIC TRANSAXLE ASSEMBLY A

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.


PROCEDURE

Hide 36100A 1.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT

a.

Clean and degrease the 4 installation holes of the transfer and transaxle setting stud bolt.


b.
C427039C01
1.208,3.323 1.521,3.479 0.313,0.156 10 false *a 2.635,3.323 2.948,3.479 0.313,0.156 10 false *b 0.74,2.354 0.896,2.552 0.156,0.198 10 false A 2.26,2.625 2.417,2.823 0.156,0.198 10 false B 2.229,0.406 2.385,0.604 0.156,0.198 10 true A 2.292,0.771 2.448,0.969 0.156,0.198 10 true A 1.49,1.198 1.646,1.396 0.156,0.198 10 true A 2.042,2.01 2.198,2.208 0.156,0.198 10 false B
*a 73 mm (2.87 in.)
*b 53 mm (2.09 in.)
V100144

Sealed Portion


Using 2 nuts, install 4 new transfer and transaxle setting stud bolts to the automatic transaxle assembly at the positions shown in the illustration.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Install the sealed side of the transfer and transaxle setting stud bolt to the automatic transaxle assembly.



Hide 2.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C361056C01
0.604,1.781 0.917,1.438 true 0.635,0.427 0.875,0.885 true 2.115,0.208 2.813,0.188 true 0.448,0.281 0.76,0.479 0.313,0.198 10 true *b 0.417,1.688 0.729,1.885 0.313,0.198 10 true *b 2.885,0.052 3.198,0.25 0.313,0.198 10 true *a
*a Matchmark
*b Key


Set the key at the top of the front oil pump drive gear and put a matchmark on the transaxle housing.


b.
C361055C02
1.479,0.188 1.573,0.188 1.573,0.188 1.74,0.688 false 1.729,1.583 2.167,1.906 false 1.281,0.063 1.594,0.26 0.313,0.198 10 false *a 2.229,1.885 2.542,2.083 0.313,0.198 10 false *b
*a Groove
*b Matchmark
V100135

MP Grease


Apply MP grease to place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.


c.
C363765C01
0.573,0.271 1.271,0.74 true 0.583,0.281 1.25,0.573 false 2.333,0.917 2.906,0.708 true 2.344,1.198 2.906,0.708 true 0.406,0.146 0.719,0.344 0.313,0.198 10 false *a 2.948,0.573 3.26,0.771 0.313,0.198 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




d.
C363766C01
0.74,0.281 1.344,0.448 true 0.76,2.01 1.344,1.594 true 2.323,0.854 2.917,0.677 true 2.333,1.167 2.906,0.677 true 0.552,0.135 0.802,0.344 0.25,0.208 10 false *a 0.583,1.906 0.833,2.115 0.25,0.208 10 false *a 2.938,0.531 3.188,0.74 0.25,0.208 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




e.
C363767C01
0.604,0.271 1.26,0.615 true 0.646,0.292 1.26,0.458 true 2.281,0.833 2.896,0.677 true 2.302,1.167 2.885,0.677 true 0.417,0.125 0.729,0.323 0.313,0.198 10 false *a 2.927,0.531 3.24,0.729 0.313,0.198 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the groove of the torque converter assembly into the key of the front oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C363763N01
2.417,0.448 2.573,0.646 0.156,0.198 10 false A

Using a vernier caliper and straightedge, measure the dimension (A) shown in the illustration and check the dimension (A).

Standard:

14 mm (0.5512 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 35151A 3.INSTALL UPPER TRANSAXLE CASE COVER

a.

Install the upper transaxle case cover to the automatic transaxle assembly and engage the 2 clips.


Hide 35104V 4.INSTALL BREATHER PLUG HOSE

a.

Install the breather plug sub-assembly to the breather plug hose.


b.

Install the breather plug hose to the No. 1 breather plug (ATM).


Hide 5.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C427020

Install the 2 wire harness clamp brackets to the automatic transaxle assembly with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.
C427019

Install the wire harness clamp bracket to the automatic transaxle assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 35150 6.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Coat the O-ring of a new transmission case plug assembly with Toyota Genuine ATF WS.


b.

Install the transmission case plug assembly to the automatic transaxle assembly.


Hide 7.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 36100 8.INSTALL TRANSFER ASSEMBLY

Hide 12303 9.INSTALL REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.
C427016N01
2.375,0.448 2.531,0.646 0.156,0.198 10 false A 2.24,1.594 2.396,1.792 0.156,0.198 10 false B 1.219,0.615 1.365,0.792 0.146,0.177 10 true C 1.313,1.448 1.458,1.625 0.146,0.177 10 true C

Install the rear engine mounting bracket sub-assembly to the automatic transaxle assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (A) → Fully tighten bolt (C)



b.

Install the wire harness clamp bracket to the rear engine mounting bracket sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12372A 10.INSTALL ENGINE MOUNTING INSULATOR LH

a.
C427012N01
0.521,1.208 0.667,1.396 0.146,0.188 10 true A 2.698,0.615 2.844,0.802 0.146,0.188 10 true B 2.323,0.26 2.469,0.448 0.146,0.188 10 true C 0.698,1.563 0.844,1.75 0.146,0.188 10 true C 1.031,0.573 1.177,0.76 0.146,0.188 10 true D

Install the engine mounting insulator LH to the automatic transaxle assembly with the 5 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A) → Fully tighten bolt (D)



Hide 12311A 11.INSTALL FRONT ENGINE MOUNTING BRACKET

a.
C427011N01
1.552,0.229 1.708,0.396 0.156,0.167 10 true A 0.865,1.594 1,1.792 0.135,0.198 10 false C 2.313,1.51 2.469,1.677 0.156,0.167 10 true B

Install the front engine mounting bracket to the automatic transaxle assembly with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A)



Hide 32907C 12.INSTALL NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

Hide 33493A 13.INSTALL TRANSMISSION OIL COOLER

Hide 14.CONNECT OUTLET NO. 3 OIL COOLER HOSE

Hide 30500 16.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C363764C01
1.698,1.063 1.927,1.063 false 1.167,1 1.479,1.198 0.313,0.198 10 false *1 1.969,0.979 2.281,1.177 0.313,0.198 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz)



b.
C378101C01
0.865,1.385 1.427,1.385 true 2.25,0.615 3.042,0.615 true 0.656,1.292 0.823,1.49 0.167,0.198 10 true *1 3.094,0.49 3.26,0.688 0.167,0.198 10 true *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
C426847N01
1.25,0.125 1.448,0.344 0.198,0.219 10 false A 1.76,0.042 1.958,0.26 0.198,0.219 10 false A 2.75,0.156 2.948,0.375 0.198,0.219 10 false A 2.833,0.677 3.031,0.896 0.198,0.219 10 false A 2.927,1.177 3.125,1.396 0.198,0.219 10 false A 2.833,1.563 3.031,1.781 0.198,0.219 10 false A 2.594,1.865 2.792,2.083 0.198,0.219 10 false B 1.99,1.969 2.188,2.156 0.198,0.188 10 false B 1.458,1.99 1.646,2.146 0.188,0.156 10 false B 0.885,0.74 1.031,0.938 0.146,0.198 10 true A

While keeping the engine assembly and automatic transaxle assembly horizontal, align the 2 knock pins with the holes in the automatic transaxle assembly and install the automatic transaxle assembly with the 10 bolts shown in the illustration.

Torque:
Bolt (A) : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt (B) : 43 N*m (438 kgf*cm, 32 ft.*lbf)

Bolt Length:
Bolt Length
(A) 55 mm (2.17 in.)
(B) 33 mm (1.30 in.)


NOTICE:
·

Confirm that the 2 knock pins are installed to the automatic transaxle assembly contact surface of the cylinder block sub-assembly before installing the automatic transaxle assembly.

·

Do not forcibly pry on the automatic transaxle assembly.

·

Check that the torque converter assembly rotates.




d.
P000601C53
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the bolt (C).

Bolt Length:

41 mm (1.61 in.)


Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the bolt immediately after applying adhesive to prevent foreign matter from attaching to it.


HINT:

The bolt (C) is in the location shown in the following step.



e.
C426848N01
1.104,1.74 1.25,1.938 0.146,0.198 10 true C

Install the bolt (C).

Torque:
Bolt (C) : 48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 20.CONNECT HOSE CLAMP

a.

Engage the clamp to connect the hose clamp to the wire harness clamp bracket.


Hide 16260 21.CONNECT WATER BY-PASS HOSE ASSEMBLY

Hide 33197C 22.INSTALL TRANSMISSION BREATHER CLAMP

Hide 35104V 23.INSTALL BREATHER PLUG HOSE

a.

Engage the 4 hose clamps to install the breather plug hose.


Hide 24.CONNECT VACUUM HOSE

a.

Engage the clamp to connect the vacuum hose to the engine mounting insulator LH.


Hide 82121 25.CONNECT ENGINE WIRE

a.
C427052C01
2.344,2.927 2.531,3.094 0.188,0.167 10 true *a 2.188,0.75 2.375,0.927 0.188,0.177 10 true *b 1.375,1.146 1.51,1.313 0.135,0.167 10 true A 1.177,1.635 1.313,1.802 0.135,0.167 10 true A 1.083,2.615 1.219,2.781 0.135,0.167 10 true A 2.74,4.448 2.875,4.615 0.135,0.167 10 true A 1.479,4.146 1.615,4.313 0.135,0.167 10 true B 3.073,3.802 3.26,3.969 0.188,0.167 10 true *c
*a Park/Neutral Position Switch Assembly Connector
*b Transmission Wire Connector
*c Connector


Connect the engine wire to the automatic transaxle assembly with the 5 bolts and engage the 3 clamps.

Torque:
Bolt (A) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt (B) : 20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Connect the connector.


c.

Connect the transmission wire connector and rotate the lever to engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



d.

Connect the park/neutral position switch assembly connector.


Hide 27.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 52132A 28.INSTALL NO. 2 FRONT BUMPER REINFORCEMENT

Hide 52618 29.INSTALL FRONT BUMPER LOWER ABSORBER

Hide 32101A 30.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Remove any remaining adhesive from the 6 drive plate and torque converter assembly setting bolts.


b.
P000601C22
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley set bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11361J 31.INSTALL FLYWHEEL HOUSING UNDER COVER

Hide 32.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION