Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086851 2GR-FKS ENGINE MECHANICAL _0420085 REAR CRANKSHAFT OIL SEAL A

2GR-FKS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Not necessary when ECM replaced with new one

*3: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*4: If the vehicle height has changed due to suspension or tire replacement

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC is output (Click here)
Code registration Engine start function See Service Bulletin for the registration method
Gas leak from exhaust system is repaired Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
·

Perform reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
Replacement of ECM
(If transaxle compensation code read from ECM)
·

Perform reset memory*2

·

Transfer transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of ECM
(If transaxle compensation code not read from ECM)
·

Perform reset memory*2

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of front bumper assembly*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*4
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 32101 2.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A419832N01
2.323,1.469 0.542,1.469 0.542,1.469 1.635,1.271 true 0.24,1.385 0.698,1.583 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-70011  (09213-70020)
09330-00021  


c.
A369436

Remove the 8 bolts, the rear drive plate spacer, the drive plate and ring gear sub-assembly.


Hide 19315 3.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.

Remove the No. 1 crankshaft position sensor plate.


Hide 11381A 4.REMOVE REAR ENGINE OIL SEAL

a.
A369437C01
2.354,1.448 1.958,1.01 true 0.698,1.396 0.375,0.563 true 2.427,1.469 2.74,1.625 0.313,0.156 10 true *a 0.26,0.375 0.573,0.531 0.313,0.156 10 false *b
*a Protective Tape
*b Cut Position


Using a knife, cut through the lip of the rear engine oil seal.


b.

Using a screwdriver with its tip wrapped with protective tape, pry out the rear engine oil seal.

NOTICE:

Be careful not to damage the crankshaft.