Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0420115 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2658  Short in Sensor with Motor Power Supply Circuit  


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2658 Short in Sensor with Motor Power Supply Circuit Problem with the voltage supplied to the position control sensor.
·

Position control ECU assembly (driver seat)

·

Slide motor (separate type front seat cushion spring assembly (driver seat))

·

Front vertical motor (power seat tilt motor assembly (driver seat))

·

Lifter motor (power seat lifter motor assembly (driver seat))

·

Reclining motor (separate type front seatback spring assembly (driver seat))

·

Wire harness or connector



WIRING DIAGRAM

B549563E06
5.458,0.656 6.073,0.854 0.615,0.198 10 false SSRS 5.448,1.833 6.063,2.031 0.615,0.198 10 false SSFV 5.458,3.01 6.073,3.208 0.615,0.198 10 false SSRL 5.458,5.052 6.073,5.25 0.615,0.198 10 false SSRR 2.188,0.563 2.344,0.76 0.156,0.198 10 false 3 3.167,0.552 3.323,0.75 0.156,0.198 10 false 2 2.188,1.729 2.344,1.927 0.156,0.198 10 false 3 3.167,1.729 3.323,1.927 0.156,0.198 10 false 2 2.406,1.063 2.865,1.26 0.458,0.198 10 false e11 0.948,3.271 1.406,3.469 0.458,0.198 10 false e13 5.188,0.552 5.5,0.75 0.313,0.198 10 false 26 3.167,2.896 3.323,3.094 0.156,0.198 10 false 2 2.188,2.906 2.344,3.104 0.156,0.198 10 false 3 5.198,1.729 5.51,1.927 0.313,0.198 10 false 10 5.208,2.906 5.521,3.104 0.313,0.198 10 false 25 2.417,1.208 4.104,1.406 1.688,0.198 10 false Slide Motor 1.177,2.26 4.448,2.865 3.271,0.604 10 false Front Vertical Motor (Power Seat Tilt Motor Assembly (Driver Seat)) 0.938,3.427 4.667,3.927 3.729,0.5 10 false Lifter Motor (Power Seat Lifter Motor Assembly (Driver Seat)) 3.156,4.948 3.313,5.146 0.156,0.198 10 false 2 2.188,4.958 2.344,5.156 0.156,0.198 10 false 3 2.281,5.458 2.74,5.656 0.458,0.198 10 false g5 2.281,5.635 4.573,5.833 2.292,0.198 10 false Reclining Motor 0.896,5.979 6.396,6.177 5.5,0.198 10 false Separate Type Front Seatback Spring Assembly (Driver Seat) 5.188,4.948 5.5,5.146 0.313,0.198 10 false 11 5.188,6.458 5.5,6.656 0.313,0.198 10 false 12 4.917,6.885 5.771,7.135 0.854,0.25 10 false e25 4.917,7.052 6.875,7.573 1.958,0.521 10 false Position Control ECU Assembly (Driver Seat) 1.177,2.104 1.635,2.302 0.458,0.198 10 false e12 5.458,6.573 6.073,6.771 0.615,0.198 10 false SGND 0.792,4 5.531,4.198 4.74,0.198 10 false Separate Type Front Seat Cushion Spring Assembly (Driver Seat)

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2658 is not output.



Result:
Result Proceed to
DTC B2658 is not output A
DTC B2658 output B



A

B

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (DRIVER SEAT)))
3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the e25 position control ECU assembly (driver seat) connector.


b.

Disconnect the e11 slide motor (separate type front seat cushion spring assembly (driver seat)) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e25-26 (SSRS) - e11-2 Always Below 1 Ω
e25-26 (SSRS) or e11-2 - Body ground Always 10 kΩ or higher
e25-12 (SGND) - e11-3 Always Below 1 Ω
e25-12 (SGND) or e11-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)
a.

Reconnect the e11 slide motor (separate type front seat cushion spring assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e11-2 - e11-3 Slide switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - FRONT VERTICAL MOTOR (POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)))

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - FRONT VERTICAL MOTOR (POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the e25 position control ECU assembly (driver seat) connector.


b.

Disconnect the e12 front vertical motor (power seat tilt motor assembly (driver seat)) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e25-10 (SSFV) - e12-2 Always Below 1 Ω
e25-10 (SSFV) or e12-2 - Body ground Always 10 kΩ or higher
e25-12 (SGND) - e12-3 Always Below 1 Ω
e25-12 (SGND) or e12-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (FRONT VERTICAL MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (FRONT VERTICAL MOTOR CIRCUIT)
a.

Reconnect the e12 front vertical motor (power seat tilt motor assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e12-2 - e12-3 Front vertical switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)))

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the e25 position control ECU assembly (driver seat) connector.


b.

Disconnect the e13 lifter motor (power seat lifter motor assembly (driver seat)) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e25-25 (SSRL) - e13-2 Always Below 1 Ω
e25-25 (SSRL) or e13-2 - Body ground Always 10 kΩ or higher
e25-12 (SGND) - e13-3 Always Below 1 Ω
e25-12 (SGND) or e13-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)
a.

Reconnect the e13 lifter motor (power seat lifter motor assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e13-2 - e13-3 Lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT)))

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the e25 position control ECU assembly (driver seat) connector.


b.

Disconnect the g5 reclining motor (separate type front seatback spring assembly (driver seat)) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e25-11 (SSRR) - g5-2 Always Below 1 Ω
e25-11 (SSRR) or g5-2 - Body ground Always 10 kΩ or higher
e25-12 (SGND) - g5-3 Always Below 1 Ω
e25-12 (SGND) or g5-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)
a.

Reconnect the g5 reclining motor (separate type front seatback spring assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
g5-2 - g5-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

11.REPLACE FRONT VERTICAL MOTOR (POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT))

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

11.REPLACE FRONT VERTICAL MOTOR (POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT))
a.

Replace the front vertical motor (power seat tilt motor assembly (driver seat)) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Recheck for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2658 is not output.



Result:
Proceed to
OK
NG



OK

END (FRONT VERTICAL MOTOR (POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)) WAS DEFECTIVE)

NG

13.REPLACE LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
13.REPLACE LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
a.

Replace the lifter motor (power seat lifter motor assembly (driver seat)) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Recheck for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2658 is not output.



Result:
Proceed to
OK
NG



OK

END (LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)) WAS DEFECTIVE)

NG

15.REPLACE SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (DRIVER SEAT))
15.REPLACE SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (DRIVER SEAT))
a.

Replace the slide motor (separate type front seat cushion spring assembly (driver seat)) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR DTC
16.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Recheck for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2658 is not output.



Result:
Proceed to
OK
NG



OK

END (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (DRIVER SEAT))

NG

17.REPLACE RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT))
17.REPLACE RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT))
a.

Replace the reclining motor (separate type front seatback spring assembly (driver seat)) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR DTC
18.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Recheck for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2658 is not output.



Result:
Proceed to
OK
NG



OK

END (RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (DRIVER SEAT)) WAS DEFECTIVE)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)