Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0420115 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Position is not Memorized  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives seat memory switch (driver door) signals from the outer mirror control ECU assembly (driver door) via CAN communication. If the SET switch is being pressed when one of the M1 or M2 switches is pressed, or if one of the M1 or M2 switches is pressed within 3 seconds of pressing the SET switch, the main body ECU (multiplex network body ECU) sends a memory request signal to the position control ECU assembly (driver seat). After receiving the request signal, the position control ECU assembly (driver seat) memorizes the location data of each motor.

WIRING DIAGRAM

B570110E06
0.094,1.167 2.052,1.625 1.958,0.458 10 false Position Control ECU Assembly (Driver Seat) 0.198,2.688 1.823,3.021 1.625,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 3.24,2.802 4.823,3.208 1.583,0.406 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.583,2.802 6.875,3.271 1.292,0.469 10 false Seat Memory Switch (Driver Door) 4.323,0.458 4.969,0.74 0.646,0.281 10 false M1 4.323,1.021 4.969,1.302 0.646,0.281 10 false M2 4.281,1.604 4.927,1.885 0.646,0.281 10 false MM 4.219,2.167 4.865,2.448 0.646,0.281 10 false GND 5.531,1.51 6.177,1.792 0.646,0.281 10 false MMRY 5.531,2.073 6.177,2.354 0.646,0.281 10 false E 5.542,0.354 6.188,0.635 0.646,0.281 10 false 1 5.542,0.938 6.188,1.219 0.646,0.281 10 false 2 4.615,0.354 5.26,0.635 0.646,0.281 10 false 2 4.625,0.938 5.271,1.219 0.646,0.281 10 false 3 4.625,1.51 5.271,1.792 0.646,0.281 10 false 1 4.625,2.073 5.271,2.354 0.646,0.281 10 false 7 5.365,0.354 6.01,0.635 0.646,0.281 10 false 3 5.365,0.938 6.01,1.219 0.646,0.281 10 false 4 5.354,1.521 6,1.802 0.646,0.281 10 false 2 5.344,2.083 5.99,2.365 0.646,0.281 10 false 1 3.25,2.625 3.896,2.906 0.646,0.281 10 false J23 5.594,2.646 6.573,2.927 0.979,0.281 10 false J21 0.698,3.375 2.667,3.594 1.969,0.219 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a restoring operation has failed, release all of the switches. The seat memory restoring function will not operate unless the switches are released.

·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the front power seat switch (driver seat).



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (SEAT MEMORY SWITCH (DRIVER DOOR))

NG

2.READ VALUE USING GTS (SEAT MEMORY SWITCH (DRIVER DOOR))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Mirror L > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 M1 switch ON or OFF ON: M1 switch on
OFF: M1 switch off
-
Seat Memory Switch2 M2 switch ON or OFF ON: M2 switch on
OFF: M2 switch off
-
Seat Memory Set SW SET switch ON or OFF ON: SET switch on
OFF: SET switch off
-
Body Electrical > Mirror L > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Set SW
50003 225 1,2,4
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (BUZZER)

NG

8.INSPECT SEAT MEMORY SWITCH (DRIVER DOOR)
3.PERFORM ACTIVE TEST USING GTS (BUZZER)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Buzzer operation OFF/ON -
Body Electrical > Driver Seat > Active Test
Tester Display
Buzzer
50004 162 5
OK:

Buzzer sounds normally.



Result:
Proceed to
OK
NG



OK

4.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

4.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)
a.

Replace the outer mirror control ECU assembly (driver door) with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
5.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

NG

6.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)
6.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)
a.

Replace the position control ECU assembly (driver seat) with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
7.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

8.INSPECT SEAT MEMORY SWITCH (DRIVER DOOR)

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) - SEAT MEMORY SWITCH (DRIVER DOOR) - BODY GROUND)

NG

REPLACE SEAT MEMORY SWITCH (DRIVER DOOR)

9.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) - SEAT MEMORY SWITCH (DRIVER DOOR) - BODY GROUND)
a.

Disconnect the J23 outer mirror control ECU assembly (driver door) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J23-1 (MM) - J21-2 (MMRY) Always Below 1 Ω
J23-1 (MM) or J21-2 (MMRY) - Body ground Always 10 kΩ or higher
J23-2 (M1) - J21-3 (1) Always Below 1 Ω
J23-2 (M1) or J21-3 (1) - Body ground Always 10 kΩ or higher
J23-3 (M2) - J21-4 (2) Always Below 1 Ω
J23-3 (M2) or J21-4 (2) - Body ground Always 10 kΩ or higher
J23-7 (GND) - Body ground Always Below 1 Ω
J21-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR