When the M1 or M2 switch of the seat memory switch (driver door) is pressed, the outer mirror control ECU assembly sends a switch signal to the main body ECU (multiplex network body ECU) via CAN communication. Then, the main body ECU (multiplex network body ECU) sends a recall request signal to the position control ECU assembly (driver seat). The position control ECU assembly (driver seat) operates each motor to move the seat to the memorized position.
The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.
The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
If a restoring operation has failed, release all of the switches. The seat memory restoring function will not operate unless the switches are released.
The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: w/ Door Control Battery
Check that each function of the power seat operates normally by using the front power seat switch (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
Each function of the power seat operates normally using the front power seat switch (driver seat).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the seat position memory function.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
Seat position memory function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Under each of the following conditions, check that the seat position restoring function operates by pressing the M1 or M2 switch.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
The ignition switch is ON, and the shift lever is in P.*1
Within 180 seconds after the driver door is opened with the ignition switch off.*2
Within 60 seconds after the driver door is opened and then closed with the ignition switch off.*3
| Result | Proceed to |
|---|---|
| Seat position restoring function does not operate at all. | A |
| Seat position restoring function does not operate when the condition is *1. | B |
·
Seat position restoring function does not operate when the condition is *2. ·
Seat position restoring function does not operate when the condition is *3. |
C |
A
B
C
Store a seat position in memory for the M1 and M2 switches.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory No1 | Seat position memorized with M1 switch | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Seat Memory No2 | Seat position memorized with M2 switch | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Tester Display |
|---|
| Seat Memory No1 |
| Seat Memory No2 |
Mem is displayed on the GTS screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the outer mirror control ECU assembly (driver door) with a new or known good one.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the seat position memory and restoring functions.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
Seat position memory and restoring functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS. (for HV Model)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift Position | Current shift state | P / R / N / D / B | Matches currently selected shift state:
P, R, N, D |
Shift state |
| Tester Display |
|---|
| Shift Position |
Read the Data List according to the display on the GTS. (for Gasoline Model)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift SW Status (P Range) | Park/neutral position switch status | ON or OFF | ON: Shift lever in P
OFF: Shift lever not in P |
- |
| Tester Display |
|---|
| Shift SW Status (P Range) |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
UA80F: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>P070513
UA80E: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>P070513
Replace the position control ECU assembly (driver seat) with a new or known good one.
Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the seat position memory and restoring functions.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
Seat position memory and restoring functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FL Door Courtesy SW | Front door courtesy light switch assembly (driver door) signal | ON or OFF | ON: Driver door open
OFF: Driver door closed |
- |
| Tester Display |
|---|
| FL Door Courtesy SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG