When the ignition switch is on and the climate control switch is operated, the air conditioning amplifier assembly receives climate control switch position signals and then sends airflow amount signals to each seat climate control blower.
Inspect the fuses for circuits related to this system before performing the following procedure.
If the auxiliary battery voltage becomes low, auxiliary battery load control will operate in order to ensure sufficient power is supplied to the power steering system. In this case, the climate control seat system may not operate.
for 2GR-FKS: Click herePower Source / Network>2GR-FKS (BATTERY / CHARGING)>CHARGING SYSTEM (w/o Stop And Start System)>ON-VEHICLE INSPECTION
for A25A-FXS: Click herePower Source / Network>A25A-FXS, A25B-FXS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
The climate control seat system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the climate control seat system after confirming that the communication system is functioning properly.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Clear DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B14B5 is not output | A |
| DTC B14B5 output | B |
A
B
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| Climate control seat does not operate (for LH) | A |
| Climate control seat does not operate (for RH) | B |
| Both climate control seats do not operate | C |
A
B
C
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Left Seat Blower | Front LH seat blower operation | OFF or ON | - |
| Tester Display |
|---|
| Front Left Seat Blower |
The seat blower operates normally.
| Result | Proceed to |
|---|---|
| Only seatback climate control blower LH does not operate | A |
| Only seat cushion climate control blower assembly LH does not operate | B |
| Both seat blowers do not operate | C |
A
B
C
Disconnect the g3 seatback climate control blower LH connector.
Disconnect the e20 seat cushion climate control blower assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| g3-1 (IG) - e20-5 (CTB) | Always | Below 1 Ω |
| g3-1 (IG) or e20-5 (CTB) - Body ground | Always | 10 kΩ or higher |
| g3-3 (BFB+) - e20-6 (BBS) | Always | Below 1 Ω |
| g3-3 (BFB+) or e20-6 (BBS) - Body ground | Always | 10 kΩ or higher |
| g3-4 (GND) - e20-4 (BFB-) | Always | Below 1 Ω |
| g3-4 (GND) or e20-4 (BFB-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the seatback climate control blower LH with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
| *a | S/HTR F/L Relay Holder |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S/HTR F/L relay holder terminal 1 - Body ground | Ignition switch ON | 11 V to 14 V |
| S/HTR F/L relay holder terminal 3 - Body ground | Always | 11 V to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e20 seat cushion climate control blower assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S/HTR F/L relay holder terminal 5 - e20-1 (IG) | Always | Below 1 Ω |
| S/HTR F/L relay holder terminal 5 or e20-1 (IG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S/HTR F/L relay holder terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Seat Cushion Climate Control Blower Assembly LH) |
Disconnect the e20 seat cushion climate control blower assembly LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e20-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| e20-1 (IG) - Body ground | Ignition switch off | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e20-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e20-7 (SIGN) - H62-14 (LOUT) | Always | Below 1 Ω |
| e20-7 (SIGN) or H62-14 (LOUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the H62 air conditioning amplifier assembly connector.
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Reconnect the e20 seat cushion climate control blower assembly LH connector.
Using an oscilloscope, check the input signal waveform.
| Item | Content |
|---|---|
| Tester Connection | H62-14 (LOUT) - Body ground |
| Tool Setting | 1 V/DIV., 0.5 ms/DIV. |
| Vehicle Condition | ·
Ignition switch ON ·
Climate control switch on (blower position) |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Right Seat Blower | Front RH seat blower operation | OFF or ON | - |
| Tester Display |
|---|
| Front Right Seat Blower |
The seat blower operates normally.
| Result | Proceed to |
|---|---|
| Only seatback climate control blower RH (separate type front seatback spring assembly (RH)) does not operate | A |
| Only seat cushion climate control blower assembly RH does not operate | B |
| Both seat blowers do not operate | C |
A
B
C
Disconnect the g1 seatback climate control blower RH (separate type front seatback spring assembly (RH)) connector.
Disconnect the e9 seat cushion climate control blower assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| g1-1 (IG) - e9-5 (CTB) | Always | Below 1 Ω |
| g1-1 (IG) or e9-5 (CTB) - Body ground | Always | 10 kΩ or higher |
| g1-3 (BFB+) - e9-6 (BBS) | Always | Below 1 Ω |
| g1-3 (BFB+) or e9-6 (BBS) - Body ground | Always | 10 kΩ or higher |
| g1-4 (GND) - e9-4 (BTB-) | Always | Below 1 Ω |
| g1-4 (GND) or e9-4 (BTB-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the seatback climate control blower RH (separate type front seatback spring assembly (RH)) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the S/HTR F/R relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | S/HTR F/R Relay Holder |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S/HTR F/R relay holder terminal 1 - Body ground | Ignition switch ON | 11 V to 14 V |
| S/HTR F/R relay holder terminal 3 - Body ground | Always | 11 V to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e9 seat cushion climate control blower assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S/HTR F/R relay holder terminal 5 - e9-1 (IG) | Always | Below 1 Ω |
| S/HTR F/R relay holder terminal 5 or e9-1 (IG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S/HTR F/R relay holder terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Seat Cushion Climate Control Blower Assembly RH) |
Disconnect the e9 seat cushion climate control blower assembly RH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e9-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| e9-1 (IG) - Body ground | Ignition switch off | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e9-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e9-7 (SIGN) - H62-13 (ROUT) | Always | Below 1 Ω |
| e9-7 (SIGN) or H62-13 (ROUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the H62 air conditioning amplifier assembly connector.
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Reconnect the e9 seat cushion climate control blower assembly RH connector.
Using an oscilloscope, check the input signal waveform.
| Item | Content |
|---|---|
| Tester Connection | H62-13 (ROUT) - Body ground |
| Tool Setting | 1 V/DIV., 0.5 ms/DIV. |
| Vehicle Condition | ·
Ignition switch ON ·
Climate control switch on (blower position) |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the climate control switch (air conditioning control assembly) with a new or known good one.
Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH (for Front Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG