Home › Drivetrain › GF2A (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY
RM37A0E _52 Drivetrain _086861 GF2A TRANSFER / 4WD / AWD _0420306 TRANSFER ASSEMBLY A

GF2A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Before installation of each part, thoroughly clean and dry it. Then apply grease or oil as necessary. Do not use alkaline chemicals to clean aluminum parts, rubber parts or precoated bolts. Also, do not use non-residue solvent or other cleaning oils to clean oil seals or rubber parts.


PROCEDURE

Hide 31364D 1.REMOVE CLUTCH CONTROL SOLENOID WIRE

a.
C426198

Disconnect the 4 clamps and 2 connectors.


b.
C429958

Remove the 2 bolts, 2 wiring harness clamp brackets and clutch control solenoid wire from the transfer assembly.


Hide 36100A 2.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

a.
C426201

Using 2 nuts, remove the 4 transfer and transaxle setting stud bolts from the transfer assembly.


Hide 36100 3.SECURE TRANSFER ASSEMBLY

a.
C426202

Secure the transfer assembly to the overhaul attachment.


Hide 36111G 4.REMOVE TRANSFER CASE STRAIGHT PIN

a.
C426203

Remove the 2 transfer case straight pins from the transfer assembly.


Hide 36114B 5.REMOVE NO. 1 TRANSFER CASE PLUG

a.
C426204

Remove the No. 1 transfer case plug and gasket from the transfer assembly.


Hide 36114H 6.REMOVE NO. 2 TRANSFER CASE PLUG

a.
C426199

Using a 10 mm socket hexagon wrench, remove the No. 2 transfer case plug and gasket from the transfer assembly.


Hide 36114H 7.REMOVE TRANSFER DRAIN PLUG

a.
C426205

Using a 10 mm socket hexagon wrench, remove the transfer drain plug and gasket from the transfer assembly.


Hide 36114L 8.REMOVE TRANSFER FILLER PLUG

a.
C426206

Using a 10 mm socket hexagon wrench, remove the transfer filler plug and gasket from the transfer assembly.


Hide 84546 9.REMOVE NO. 1 4 WHEEL DRIVE POSITION SWITCH

a.
C426207

Remove the No. 1 4 wheel drive position switch from the transfer assembly.


Hide 36111H 10.REMOVE TRANSFER CASE BREATHER PLUG

a.
C426208

Remove the transfer case breather plug from the transfer assembly.


Hide 36113D 12.REMOVE TRANSFER CASE OIL SEAL RH

a.
C426209C01
0.385,0.729 0.469,0.729 0.469,0.729 0.531,0.5 false 0.281,0.219 0.698,0.333 false 0.115,0.146 0.427,0.302 0.313,0.156 10 false *1 0.094,0.646 0.479,0.833 0.385,0.188 10 false SST
*1 Transfer Case Oil Seal RH


Using SST, remove the transfer case oil seal RH from the transfer assembly.

SST
09308-00010  

NOTICE:

Do not scratch the press-fitting surface of the transfer case oil seal RH.



Hide 13.INSPECT TOTAL PRELOAD

NOTICE:
·

When replacing the transfer output shaft companion flange sub-assembly and transfer case oil seal, be sure to check the preload.

·

If the transfer output shaft companion flange sub-assembly and transfer case oil seal were replaced without checking the preload, replace the transfer assembly.



a.
C429752

Using a torque wrench, check the total preload (starting torque) with the teeth of the transfer driven pinion and transfer ring gear in contact.

HINT:
·

The torque wrench should be installed as shown in the illustration.

·

Record the measured value as it is used during assembly.




Hide 14.REMOVE OUTPUT SHAFT COMPANION FLANGE NUT

a.
C429753C01
1.625,0.792 1.104,0.417 1.104,0.417 0.896,0.417 true 1.573,1.115 1.125,0.781 1.125,0.781 0.917,0.781 true 0.708,0.323 0.938,0.521 0.229,0.198 10 false *a 0.719,0.688 0.948,0.885 0.229,0.198 10 false *b
*a Matchmark
*b Transfer Driven Pinion


Place a matchmark on the transfer output shaft companion flange sub-assembly as shown in the illustration.

HINT:

Place a matchmark aligned with the groove on the transfer driven pinion.



b.
C429754C01
1.271,2.115 1.427,2.115 1.427,2.115 1.833,2.469 true 1.094,2.031 1.406,2.229 0.313,0.198 10 false *a
*a Transfer Driven Pinion


Using a screwdriver and hammer, unstake the output shaft companion flange nut.

NOTICE:
·

Completely unstake the output shaft companion flange nut.

·

Do not damage the threads of the transfer driven pinion.




c.

Remove the output shaft companion flange nut from the transfer assembly.


Hide 33309 15.REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.
C429755C01
0.969,2.302 1.188,2.302 1.188,2.302 1.688,1.729 true 0.854,1.448 1.073,1.448 1.073,1.448 1.427,1.042 false 2.781,1.021 3.094,1.177 0.313,0.156 10 false *a 0.656,0.552 0.969,0.708 0.313,0.156 10 false *b 0.635,2.229 1.052,2.563 0.417,0.333 10 false SST 0.542,1.375 0.958,1.708 0.417,0.333 10 false SST
*a Turn
*b Hold


Using SST, remove the transfer output shaft companion flange sub-assembly from the transfer assembly.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030)
09956-03090  


Hide 36111X 16.REMOVE TRANSFER CASE OIL SEAL