Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM37A0E _56 Audio / Visual / Telematics _086877 AUDIO / VIDEO _0420540 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the audio and visual system connected to the AVC-LAN (communication bus) transmits signals via AVC-LAN communication.

If a short to +B or short to ground occurs in an AVC-LAN communication line, the audio and visual system will not function normally because communication is not possible.

WIRING DIAGRAM

E276615E60
2.969,2.219 4.948,2.406 1.979,0.188 10 false : AVC-LAN Communication Line 0.698,1.458 1.156,1.656 0.458,0.198 10 false R16 5.115,0.583 5.573,0.781 0.458,0.198 10 false TX+ 4.615,1.615 7.156,1.927 2.542,0.313 10 false Radio and Display Receiver Assembly 0.688,1.635 2.688,1.896 2,0.26 10 false Television Display Assembly 4.615,1.448 5.073,1.646 0.458,0.198 10 false H1 5.125,0.979 5.583,1.177 0.458,0.198 10 false TX- 4.865,0.438 5.167,0.688 0.302,0.25 10 false 19 4.865,0.823 5.219,1.083 0.354,0.26 10 false 20 1.75,0.573 2.208,0.771 0.458,0.198 10 false TX1+ 1.781,0.948 2.167,1.156 0.385,0.208 10 false TX1- 2.177,0.448 2.375,0.625 0.198,0.177 10 false 4 2.177,0.833 2.375,1.01 0.198,0.177 10 false 5


CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION


HINT:

The radio and display receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly.


b.
E394515C28
1.583,0.813 1.99,1.031 0.406,0.219 2.656,2.5 2.5,1.99 false 1.885,2.521 2.177,2 false 1.688,0.844 2,1.042 0.313,0.198 10 false H1 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 2.583,2.552 3.052,2.76 0.469,0.208 10 false TX+ 1.75,2.552 2.156,2.792 0.406,0.24 10 false TX-
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H1-19 (TX+) - H1-20 (TX-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the H1 radio and display receiver assembly connector.


b.

Disconnect the R16 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R16-4 (TX1+) - H1-19 (TX+) Always Below 1 Ω
R16-5 (TX1-) - H1-20 (TX-) Always Below 1 Ω
R16-4 (TX1+) or H1-19 (TX+) - Body ground Always 10 kΩ or higher
R16-5 (TX1-) or H1-20 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY