Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM37A0E _56 Audio / Visual / Telematics _086877 AUDIO / VIDEO _0420540 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Microphone Circuit  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly and telephone microphone assembly, and the map light assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

E377468E27
0.385,3.292 1.771,3.844 1.385,0.552 10 false Telephone Microphone Assembly 2.573,3.292 3.99,3.917 1.417,0.625 10 false Map Light Assembly 5.542,3.469 6.74,3.917 1.198,0.448 10 false Radio and Display Receiver Assembly 2.542,2.854 2.917,3.208 0.375,0.354 10 false B 2.531,1.917 2.906,2.271 0.375,0.354 10 false B 2.531,1.448 2.906,1.802 0.375,0.354 10 false B 2.531,0.969 2.906,1.323 0.375,0.354 10 false B 3.677,0.948 4.052,1.302 0.375,0.354 10 false R11 3.667,1.438 4.042,1.792 0.375,0.354 10 false R11 3.667,1.906 4.042,2.26 0.375,0.354 10 false R11 3.656,2.354 4.031,2.708 0.375,0.354 10 false R11 3.677,2.854 4.052,3.208 0.375,0.354 10 false R11 3.708,2.656 4.083,3.01 0.375,0.354 10 false 14 3.698,2.156 4.073,2.51 0.375,0.354 10 false 11 3.698,1.24 4.063,1.594 0.365,0.354 10 false 13 3.75,1.708 4.115,2.063 0.365,0.354 10 false 5 3.75,0.74 4.115,1.094 0.365,0.354 10 false 4 2.542,0.76 2.906,1.115 0.365,0.354 10 false 5 2.552,1.24 2.917,1.594 0.365,0.354 10 false 3 2.542,1.719 2.906,2.073 0.365,0.354 10 false 2 2.552,2.656 2.917,3.01 0.365,0.354 10 false 1 3.188,2.854 3.625,3.177 0.438,0.323 10 false SNS2 3.26,2.344 3.677,2.604 0.417,0.26 10 false GND 3.188,1.896 3.677,2.198 0.49,0.302 10 false MCO- 3.146,1.427 3.635,1.76 0.49,0.333 10 false MCO+ 3.146,0.938 3.635,1.271 0.49,0.333 10 false MACC 5.708,0.969 6.198,1.302 0.49,0.333 10 false MACC 5.698,1.448 6.188,1.781 0.49,0.333 10 false MIN+ 5.708,1.917 6.198,2.25 0.49,0.333 10 false MIN- 5.698,2.385 6.188,2.719 0.49,0.333 10 false SGND 5.708,2.865 6.146,3.188 0.438,0.323 10 false SNS2 5.479,2.75 5.854,3.104 0.375,0.354 10 false 25 5.479,2.281 5.854,2.635 0.375,0.354 10 false 24 5.479,1.802 5.854,2.156 0.375,0.354 10 false 22 5.479,1.323 5.854,1.677 0.375,0.354 10 false 21 5.469,0.844 5.844,1.198 0.375,0.354 10 false 23 5.552,3.292 5.948,3.719 0.396,0.427 10 false H2 4.625,2.208 4.906,2.479 0.281,0.271 10 false * 0.479,4.26 1.979,4.521 1.5,0.26 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION


PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio and display receiver assembly) in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check results are normal.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H2 radio and display receiver assembly connector.


b.

Disconnect the R11 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-25 (SNS2) - R11-14 (SNS2) Always Below 1 Ω
H2-23 (MACC) - R11-4 (MACC) Always Below 1 Ω
H2-21 (MIN+) - R11-13 (MCO+) Always Below 1 Ω
H2-22 (MIN-) - R11-5 (MCO-) Always Below 1 Ω
H2-25 (SNS2) or R11-14 (SNS2) - Body ground Always 10 kΩ or higher
H2-23 (MACC) or R11-4 (MACC) - Body ground Always 10 kΩ or higher
H2-21 (MIN+) or R11-13 (MCO+) - Body ground Always 10 kΩ or higher
H2-22 (MIN-) or R11-5 (MCO-) - Body ground Always 10 kΩ or higher
H2-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the H2 radio and display receiver assembly connector.


b.

Connect the R11 map light assembly connector.


c.
E412759C54
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 false 2.188,2.885 1.927,2.146 false 2.813,2.604 2.052,2.156 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.625,0.76 1.938,0.958 0.313,0.198 10 false H2 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.094,2.896 2.729,3.115 0.635,0.219 10 false MACC 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H2-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-24 (SGND) - Body ground Always Below 1 Ω
H2-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the B telephone microphone assembly connector.


c.
E430891C02
2.26,1.135 1.948,0.615 false 2.094,1.76 2.25,1.344 false 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 1.729,0.417 2.24,0.625 0.51,0.208 10 false MCO- 1.917,1.781 2.448,2.042 0.531,0.26 10 false SNS2
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (SNS2) - 5 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

7.INSPECT MAP LIGHT ASSEMBLY
5.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the H2 radio and display receiver assembly connector.


b.

Connect the R11 map light assembly connector.


c.

Turn the ignition switch to ACC.


d.
E437153C01
1.542,0.344 1.917,0.594 0.375,0.25 2.229,1.5 1.979,0.958 false 2.115,2.26 2.385,1.719 false 1.875,2.292 2.49,2.49 0.615,0.198 10 false MCO+ 1.781,0.74 2.396,0.938 0.615,0.198 10 false MCO- 1.635,0.385 2.25,0.583 0.615,0.198 10 false R11 2.813,3.438 3.427,3.635 0.615,0.198 10 false GND 0.135,0.094 0.75,0.292 0.615,0.198 10 false *a
*a Component without harness connected
(Map Light Assembly)


Connect an oscilloscope to terminals 13 (MCO+) and 5 (MCO-) of the R11 map light assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal R11-13 (MCO+) - R11-5 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC

2.

Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

6.INSPECT MAP LIGHT ASSEMBLY
6.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E437127C02
1.458,0.396 1.844,0.646 0.385,0.25 1.479,2.813 1.875,3.063 0.396,0.25 2.667,2.104 2.854,1.646 false 2.177,2.083 2.417,1.646 false 2.25,1.417 2.677,0.906 false 0.521,0.385 0.833,0.583 0.313,0.198 10 false *a 0.521,2.719 0.833,2.917 0.313,0.198 10 false *b 1.969,2.146 2.469,2.365 0.5,0.219 10 false MCO+ 2.521,0.688 3,0.896 0.479,0.208 10 false MCO- 2.5,2.167 2.99,2.396 0.49,0.229 10 false GND 1.635,2.854 1.948,3.052 0.313,0.198 10 false B 1.542,0.438 2.021,0.646 0.479,0.208 10 false R11
*a Component without harness connected
(Map Light Assembly (Radio and Display Receiver Assembly Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R11-13 (MCO+) - B-3 Always Below 1 Ω
R11-5 (MCO-) - B-2 Always Below 1 Ω
R11-13 (MCO+) or B-3 - R11-11 (GND) Always 10 kΩ or higher
R11-5 (MCO-) or B-2 - R11-11 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

7.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E437127C01
1.458,0.396 1.844,0.646 0.385,0.25 1.479,2.813 1.875,3.063 0.396,0.25 3.063,2.083 2.854,1.635 false 2.26,1.427 1.823,0.979 false 1.823,2.156 2.25,1.646 false 0.521,0.385 0.833,0.583 0.313,0.198 10 false *a 0.521,2.719 0.833,2.917 0.313,0.198 10 false *b 1.615,2.188 2.115,2.406 0.5,0.219 10 false SNS2 1.542,0.75 2.021,0.958 0.479,0.208 10 false MCO- 2.917,2.146 3.406,2.375 0.49,0.229 10 false GND 1.635,2.854 1.948,3.052 0.313,0.198 10 false B 1.521,0.427 2,0.635 0.479,0.208 10 false R11
*a Component without harness connected
(Map Light Assembly (Radio and Display Receiver Assembly Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - R11-14 (SNS2) Always Below 1 Ω
B-2 - R11-5 (MCO-) Always Below 1 Ω
B-1 or R11-14 (SNS2) - R11-11 (GND) Always 10 kΩ or higher
B-2 or R11-5 (MCO-) - R11-11 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY