Use the following procedure to troubleshoot the air conditioning system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the auxiliary battery voltage with the ignition switch off.
11 to 14 V
If the auxiliary battery voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
Using the GTS, check the Data List item "Operation Limitation Control History Count".
| Tester Display |
|---|
| Operation Limitation Control History Count (Level1) |
| Operation Limitation Control History Count (Level2) |
If a value other than zero is displayed for "Operation Limitation Control History Count (Level1)" or "Operation Limitation Control History Count (Level2)", air conditioning system operation may have been limited in the past. If the operation is still limited, the message "High Power Consumption Partial Limit on AC/Heater Operation" will be displayed on the multi-information display in the combination meter assembly. In this case, inspect the charging system.
Click herePower Source / Network>A25A-FXS, A25B-FXS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, check for CAN communication system DTCs.
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Check for DTCs and note any codes that are output.
Air Conditioner
Hybrid Control (for P1C7C49)
Main Body (for B1279)
Rain and/or Humidity Sensor (for B14A8 / B14A9 / B14AA)
Clear the DTCs.
Air Conditioner
Hybrid Control (for P1C7C49)
Main Body (for B1279)
Rain and/or Humidity Sensor (for B14A8 / B14A9 / B14AA)
Recheck for DTCs. Based on the DTCs output above, try to force output of the air conditioning system DTC by simulating the operation indicated by the DTC.
Air Conditioner
Hybrid Control (for P1C7C49)
Main Body (for B1279)
Rain and/or Humidity Sensor (for B14A8 / B14A9 / B14AA)
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Operate each switch on the air conditioning control assembly and check that the switches of the air conditioning system operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the blower switch on the air conditioning control assembly and check that the blower control operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the recirculation/fresh switch on the air conditioning control assembly and check that the air inlet control operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the air outlet mode switch on the air conditioning control assembly and check that the air outlet control operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the temperature adjustment switches on the air conditioning control assembly and check that cool air is blown from the registers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the temperature adjustment switches on the air conditioning control assembly and check that warm air is blown from the air registers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT