Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model) › 2020.02–2021.10
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0420832 AIR CONDITIONING SYSTEM(for HV Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  B1279  Lost Communication with Humidity/Rain Sensor LIN  


DESCRIPTION

The main body ECU (multiplex network body ECU) and windshield humidity sensor communicate via LIN communication.

The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1279 Lost Communication with Humidity/Rain Sensor LIN Lost communication with windshield humidity sensor
·

Harness or connector

·

Main body ECU (multiplex network body ECU)

·

Windshield humidity sensor (air conditioning thermistor assembly)*2

·

Windshield humidity sensor (rain sensor)*3


Memorized
(10 sec. or more)*1

*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.

*2: w/o Auto Wiper System

*3: w/ Auto Wiper System

WIRING DIAGRAM

E432272E01
4.875,1.75 6.542,2.115 1.667,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 4.51,1.26 4.969,1.458 0.458,0.198 10 false H42 0.344,2.698 4.938,2.958 4.594,0.26 10 false Windshield Humidity Sensor (Air Conditioning Thermistor Assembly)*1 0.333,2.531 0.604,2.74 0.271,0.208 10 false R4 4.917,1.26 5.281,1.469 0.365,0.208 10 false LIN3 1.688,1.25 2.063,1.448 0.375,0.198 10 false MPX 4.604,1.063 4.771,1.271 0.167,0.208 10 false 3 2.104,1.115 2.271,1.323 0.167,0.208 10 false 3 1.802,1.958 2.167,2.167 0.365,0.208 10 false ES 1.76,0.51 2.125,0.719 0.365,0.208 10 false SIG 2.406,0.656 3.427,0.854 1.021,0.198 10 false ECU-IG1 NO. 4 0.948,3.365 2.667,3.563 1.719,0.198 10 false : LIN Communication Line 2.104,0.406 2.271,0.615 0.167,0.208 10 false 4 2.115,1.844 2.281,2.052 0.167,0.208 10 false 2 3.979,0.5 5.542,0.729 1.563,0.229 10 false from IG1-NO. 1 Relay 0.344,2.958 3.448,3.177 3.104,0.219 10 false Windshield Humidity Sensor (Rain Sensor)*2 4.042,3.167 5.927,3.375 1.885,0.208 10 false *1: w/o Auto Wiper System 4.042,3.417 5.927,3.625 1.885,0.208 10 false *2: w/ Auto Wiper System

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B1279 is output (w/o Auto Wiper System) A
DTC B1279 is output (w/ Auto Wiper System) B
DTC B1279 and B1373 are output C



A

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD HUMIDITY SENSOR (AIR CONDITIONING THERMISTOR ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

B

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD HUMIDITY SENSOR (RAIN SENSOR) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD HUMIDITY SENSOR (AIR CONDITIONING THERMISTOR ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H42 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the R4 windshield humidity sensor (air conditioning thermistor assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R4-3 (MPX) - H42-3 (LIN3) Always Below 1 Ω
R4-3 (MPX) or H42-3 (LIN3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Disconnect the H42 main body ECU (multiplex network body ECU) connector.


b.

Check for voltage and pulses according to the value(s) in the table below.

E432365C01
4.604,0.552 5.031,0.802 0.427,0.25 3.938,0.854 4.354,1.177 true 1.938,1.156 2.344,1.156 true 4.01,0.208 4.323,0.365 0.313,0.156 10 false *a 4.698,0.604 5.156,0.802 0.458,0.198 10 false H42 3.615,0.771 4.229,0.969 0.615,0.198 10 false LIN3 2.396,1.073 2.854,1.271 0.458,0.198 10 false H42
*a Component without harness connected
(Main Body ECU (Multiplex Network Body ECU))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
H42-3 (LIN3) - Body ground Ignition switch off Below 1 V
Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD HUMIDITY SENSOR (AIR CONDITIONING THERMISTOR ASSEMBLY))

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD HUMIDITY SENSOR (AIR CONDITIONING THERMISTOR ASSEMBLY))
a.

Disconnect the R4 windshield humidity sensor (air conditioning thermistor assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R4-4 (SIG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
R4-2 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD HUMIDITY SENSOR (AIR CONDITIONING THERMISTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD HUMIDITY SENSOR (RAIN SENSOR) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H42 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the R4 windshield humidity sensor (rain sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R4-3 (MPX) - H42-3 (LIN3) Always Below 1 Ω
R4-3 (MPX) or H42-3 (LIN3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Disconnect the H42 main body ECU (multiplex network body ECU) connector.


b.

Check for voltage and pulses according to the value(s) in the table below.

E432365C01
4.604,0.552 5.031,0.802 0.427,0.25 3.938,0.854 4.354,1.177 true 1.938,1.156 2.344,1.156 true 4.01,0.208 4.323,0.365 0.313,0.156 10 false *a 4.698,0.604 5.156,0.802 0.458,0.198 10 false H42 3.615,0.771 4.229,0.969 0.615,0.198 10 false LIN3 2.396,1.073 2.854,1.271 0.458,0.198 10 false H42
*a Component without harness connected
(Main Body ECU (Multiplex Network Body ECU))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
H42-3 (LIN3) - Body ground Ignition switch off Below 1 V
Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD HUMIDITY SENSOR (RAIN SENSOR))

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD HUMIDITY SENSOR (RAIN SENSOR))
a.

Disconnect the R4 windshield humidity sensor (rain sensor) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R4-4 (SIG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
R4-2 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD HUMIDITY SENSOR (RAIN SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR