Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Gasoline Model with Automatic Air Conditioning System)
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0420833 AIR CONDITIONING SYSTEM(for Gasoline Model with Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Gasoline Model with Automatic Air Conditioning System)  B149A  Communication Malfunction (Rear Bus Ic)  


DESCRIPTION

The No. 2 air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors.

The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the No. 2 air conditioning harness assembly.

Each servo motor sends damper position information to the air conditioning amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B149A Communication Malfunction (Rear Bus Ic) Error or open in communication line between air conditioning amplifier assembly and any of the following servo motors.
·

Rear mode damper servo sub-assembly

·

Rear air mix damper servo sub-assembly


·

No. 2 air conditioning harness assembly

·

Air conditioning amplifier assembly

·

Harness or connector


Memorized
(10 sec. or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.

WIRING DIAGRAM

E432288E01
0.76,5.333 2.469,5.552 1.708,0.219 10 false : LIN Communication Line 2.427,1.219 2.74,1.417 0.313,0.198 10 false IC 2.427,3.427 2.74,3.625 0.313,0.198 10 false IC 0.302,1.115 1.302,1.51 1,0.396 10 false Rear Passenger Side Mode 0.302,3.354 1.313,3.74 1.01,0.385 10 false Rear Passenger Side Air Mix 0.188,2 2.938,2.26 2.75,0.26 10 false Rear Mode Damper Servo Sub-assembly 0.188,4.229 2.948,4.479 2.76,0.25 10 false Rear Air Mix Damper Servo Sub-assembly 2.875,4.604 4.75,5.021 1.875,0.417 10 false No. 2 Air Conditioning Harness Assembly 5.5,4.927 7.042,5.292 1.542,0.365 10 false Air Conditioning Amplifier Assembly 6.021,0.833 6.583,1.052 0.563,0.219 10 false RBUS 6.021,1.229 6.635,1.427 0.615,0.198 10 false RBBU 6.021,1.615 6.635,1.813 0.615,0.198 10 false RBUG 5.604,0.823 6.063,1.021 0.458,0.198 10 false H64 5.604,1.229 6.063,1.427 0.458,0.198 10 false H64 5.604,1.615 6.063,1.813 0.458,0.198 10 false H64 5.688,0.635 5.844,0.833 0.156,0.198 10 false 7 5.688,1.031 5.844,1.229 0.156,0.198 10 false 2 5.688,1.427 5.844,1.625 0.156,0.198 10 false 3 4.615,0.833 5.073,1.031 0.458,0.198 10 false M15 4.615,1.229 5.073,1.427 0.458,0.198 10 false M15 4.615,1.625 5.073,1.823 0.458,0.198 10 false M15 4.719,0.635 4.875,0.833 0.156,0.198 10 false 3 4.719,1.427 4.875,1.625 0.156,0.198 10 false 2 4.719,1.042 4.875,1.24 0.156,0.198 10 false 4 4.052,0.656 4.615,0.875 0.563,0.219 10 false RBUS 4.052,1.104 4.667,1.302 0.615,0.198 10 false RBBU 4.063,1.49 4.677,1.688 0.615,0.198 10 false RBUG

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SERVO PULSE)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Air Mix Servo Targ Pulse Rear air mix damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 213 to 258 pulses
A/O Servo Pulse(Rr D) Rear mode damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 200 to 276 pulses
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Air Mix Servo Targ Pulse
50004 121 36
Body Electrical > Air Conditioner > Active Test
Tester Display
A/O Servo Pulse(Rr D)
50004 121 56
OK:

Damper servo motor is operated.



Result:
Result Proceed to
All damper servo motors are not operated A
Any damper servo motor is not operated B
All damper servo motors are operated C



A

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

B

REPLACE NO. 2 AIR CONDITIONING HARNESS ASSEMBLY

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Disconnect the H64 air conditioning amplifier assembly connector.

E432369C01
2.25,0.188 2.677,0.427 0.427,0.24 1.458,2.271 1.802,2.271 1.802,2.271 2.896,0.927 true 1.469,1.99 1.698,1.99 1.698,1.99 2.01,0.938 true 1.458,2.563 1.896,2.563 1.896,2.563 2.844,1.063 true 2.229,3.146 2.688,3.344 0.458,0.198 10 false GND 2.344,0.229 2.802,0.427 0.458,0.198 10 false H64 1.677,0.135 1.99,0.333 0.313,0.198 10 false *a 1.031,2.49 1.646,2.688 0.615,0.198 10 false RBUS 1.031,2.198 1.646,2.396 0.615,0.198 10 false RBBU 1.031,1.917 1.646,2.115 0.615,0.198 10 false RBUG
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H64-3 (RBUG) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H64-2 (RBBU) - H64-3 (RBUG) Ignition switch off 11 to 14 V



d.

Using an oscilloscope, check the waveform.

Item Content
Tester Connection H64-7 (RBUS) - H64-3 (RBUG)
Tool Setting 2 V/DIV., 20 μs/DIV.
Condition Ignition switch ON

OK:

The waveform displays properly.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 2 AIR CONDITIONING HARNESS ASSEMBLY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 2 AIR CONDITIONING HARNESS ASSEMBLY)
a.
E432370C01
1.51,0.177 1.917,0.448 0.406,0.271 1.646,1.24 2.219,0.573 2.219,0.573 2.5,0.573 true 1.813,1.24 2.292,0.833 2.292,0.833 2.5,0.833 true 1.969,1.24 2.292,1.125 2.292,1.125 2.49,1.125 true 1.594,0.229 2.052,0.427 0.458,0.198 10 false M15 0.813,0.292 1.125,0.49 0.313,0.198 10 false *a 2.594,0.75 3.208,0.948 0.615,0.198 10 false RBUS 2.594,1.052 3.208,1.25 0.615,0.198 10 false RBBU 2.594,0.479 3.208,0.677 0.615,0.198 10 false RBUG 0.24,3.698 0.854,3.896 0.615,0.198 10 false GND
*a Front view of wire harness connector
(to No. 2 Air Conditioning Harness Assembly)


Connect the H64 air conditioning amplifier assembly connector.


b.

Disconnect the M15 No. 2 air conditioning harness assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M15-2 (RBUG) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M15-4 (RBBU) - M15-2 (RBUG) Ignition switch off 11 to 14 V



e.

Using an oscilloscope, check the waveform.

Item Content
Tester Connection M15-3 (RBUS) - M15-2 (RBUG)
Tool Setting 2 V/DIV., 20 μs/DIV.
Condition Ignition switch ON

OK:

The waveform displays properly.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 AIR CONDITIONING HARNESS ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 2 AIR CONDITIONING HARNESS ASSEMBLY)