Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Gasoline Model with Automatic Air Conditioning System)
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0420833 AIR CONDITIONING SYSTEM(for Gasoline Model) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Gasoline Model)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

If refrigerant pressure does not decrease when the engine is running and the A/C switch is turned off, the following factors may be the cause.

Symptom Factor
·

Cooler compressor assembly does not stop operating

·

Refrigerant pressure does not decrease when A/C switch is turned off


·

Short to +B in air conditioning amplifier assembly circuit malfunction

·

A/C COMP relay malfunction

·

Magnet clutch assembly malfunction

·

Harness or connector



WIRING DIAGRAM

E432292E01
0.208,1.26 1.771,1.615 1.563,0.354 10 false from IG1-NO. 1 Relay 0.635,0.792 1.656,1.01 1.021,0.219 10 false from ALT Fuse 1.948,1.417 2.979,1.625 1.031,0.208 10 false ECU-IG1 NO. 3 2.083,0.938 2.917,1.156 0.833,0.219 10 false A/C COMP 3.031,1.531 3.865,1.802 0.833,0.271 10 false A/C COMP 6.021,1.25 6.49,1.479 0.469,0.229 10 false MGC 5.625,1.052 5.938,1.292 0.313,0.24 10 false 19 5.604,1.26 5.969,1.448 0.365,0.188 10 false H63 5.5,3.573 7.042,4 1.542,0.427 10 false Air Conditioning Amplifier Assembly 2.99,1.125 3.177,1.323 0.188,0.198 10 false 1 3.646,1.125 3.833,1.323 0.188,0.198 10 false 2 2.99,0.677 3.177,0.875 0.188,0.198 10 false 3 3.656,0.677 3.844,0.875 0.188,0.198 10 false 5 3.99,2.677 4.365,2.885 0.375,0.208 10 false MG+ 4.396,2.677 4.583,2.875 0.188,0.198 10 false 3 2.625,3.563 2.979,3.74 0.354,0.177 10 false C60 2.625,3.729 4.24,3.948 1.615,0.219 10 false Magnet Clutch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT A/C COMP RELAY (MAGNET-CLUTCH RELAY)

OK

2.CHECK HARNESS AND CONNECTOR (A/C COMP RELAY (MAGNET-CLUTCH RELAY) - POWER SOURCE)

NG

REPLACE A/C COMP RELAY (MAGNET-CLUTCH RELAY)

2.CHECK HARNESS AND CONNECTOR (A/C COMP RELAY (MAGNET-CLUTCH RELAY) - POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (A/C COMP relay (magnet-clutch relay)) - Body ground Always 11 to 14 V
1 (A/C COMP relay (magnet-clutch relay)) - Body ground Ignition switch off Below 1 V
1 (A/C COMP relay (magnet-clutch relay)) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (A/C COMP RELAY (MAGNET-CLUTCH RELAY) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (A/C COMP RELAY (MAGNET-CLUTCH RELAY) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the H63 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (A/C COMP relay (magnet-clutch relay)) - H63-19 (MGC) Always Below 1 Ω
2 (A/C COMP relay (magnet-clutch relay)) or H63-19 (MGC) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (A/C COMP RELAY (MAGNET-CLUTCH RELAY) - MAGNET CLUTCH ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (A/C COMP RELAY (MAGNET-CLUTCH RELAY) - MAGNET CLUTCH ASSEMBLY AND BODY GROUND)
a.

Disconnect the C60 magnet clutch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (A/C COMP relay (magnet-clutch relay)) - C60-3 (MG+) Always Below 1 Ω
5 (A/C COMP relay (magnet-clutch relay)) or C60-3 (MG+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH ASSEMBLY - BODY GROUND)
a.

Install the A/C COMP relay (magnet-clutch relay).


b.

Connect the C60 magnet clutch assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C60-3 (MG+) - Body ground Engine running
(A/C switch: Off)
Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR