Home › Engine / Hybrid System › 2GR-FKS (LUBRICATION) › OIL PUMP › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086856 2GR-FKS LUBRICATION _0420913 OIL PUMP A

2GR-FKS LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during timing chain cover assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Not necessary when ECM replaced with new one

*3: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*4: If the vehicle height has changed due to suspension or tire replacement

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC is output (Click here)
Code registration Engine start function See Service Bulletin for the registration method
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of fuel injector assembly (for port injection)

·

Replacement of fuel injector assembly (for direct injection)

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
·

Perform reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
Replacement of ECM
(If transaxle compensation code read from ECM)
·

Perform reset memory*2

·

Transfer transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of ECM
(If transaxle compensation code not read from ECM)
·

Perform reset memory*2

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of front bumper assembly*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*4
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 11310 3.REMOVE TIMING CHAIN COVER ASSEMBLY

a.
A369463C01
0.719,2.854 1.031,3.01 0.313,0.156 10 false *a 2.531,2.74 2.844,2.896 0.313,0.156 10 false *a
*a Nut


w/ Stud Bolt:

i.

Remove the 23 bolts and 2 nuts shown in the illustration.



b.
A457607

w/o Stud Bolt:

i.

Remove the 25 bolts shown in the illustration.



c.
A369464C01
0.542,1.698 1.583,4.323 1.583,4.323 2.688,3.052 true 0.594,2.927 1.573,4.333 1.573,4.333 2.427,3.958 true 1.094,4.083 1.563,4.333 true 1.5,4.375 1.813,4.531 0.313,0.156 10 false *a
*a Protective Tape


Remove the timing chain cover assembly by prying between the timing chain cover assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain cover assembly.



d.
A369465

Remove the oil pump gasket from the cylinder block sub-assembly.