Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for Gasoline Model LHD)
RM37A0E _54 Brake _086869 BRAKE SYSTEM (OTHER) _0420925 BRAKE BOOSTER(for Gasoline Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for Gasoline Model LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Learning can also be performed using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.



PROCEDURE

Hide 1.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53808A 2.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 3.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 4.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 5.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 6.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 7.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 55704B 8.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 9.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 73900 10.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 11.LOOSEN LOCK NUT

a.
C425738C01
2.833,0.667 2.167,0.667 2.167,0.667 1.885,1 true 1.094,1.604 1.51,1.604 1.51,1.604 1.677,1.104 true 0.927,1.521 1.104,1.708 0.177,0.188 10 true *1 2.865,0.583 3.052,0.76 0.188,0.177 10 true *2
*1 Lock Nut
*2 Brake Master Cylinder Push Rod Clevis


Loosen the lock nut of the brake master cylinder push rod clevis.


Hide 44778 13.DISCONNECT CONNECTOR TO CHECK VALVE HOSE

a.
C425737

Slide the clip and disconnect the connector to check valve hose from the brake booster assembly.


Hide 14.DISCONNECT CONNECTOR

a.
C425739

Disconnect the connector.


Hide 44610 15.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C425723

Remove the 4 nuts and push the brake booster assembly toward the engine compartment.

NOTICE:

Do not apply excessive force to the brake lines.



b.

Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.


c.

Remove the brake booster assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines.



Hide 44785 16.REMOVE BRAKE BOOSTER GASKET