Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for HV Model LHD)
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420929 BRAKE ACTUATOR(for HV Model LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for HV Model LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of brake actuator assembly
1.

Bleed air

2.

Perform "Calibration"


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the ignition switch is first turned to ON (Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



PROCEDURE

Hide 1.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53808A 3.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 4.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 5.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 6.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 7.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 8.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 55704B 9.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 10.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C426221C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C426792

Remove the bolt to separate the brake lines.


c.
C426222C01
0.99,0.281 1.323,0.281 1.323,0.281 1.573,0.646 true 1.844,0.583 2.125,0.333 2.125,0.333 2.375,0.333 true 1.771,1.865 1.771,1.531 true 1.156,1.604 1.156,1.104 true 2.094,1.813 2.094,1.229 true 0.813,0.531 1.146,0.531 1.146,0.531 1.396,0.781 true 1.698,1.865 1.885,2.042 0.188,0.177 10 true *a 2.021,1.813 2.208,2 0.188,0.188 10 true *b 1.073,1.604 1.25,1.781 0.177,0.177 10 true *c 0.656,0.448 0.833,0.615 0.177,0.167 10 true *d 0.833,0.188 1,0.365 0.167,0.177 10 true *e 2.396,0.25 2.563,0.417 0.167,0.167 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly RH
*d To Front Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH
*f To Rear Wheel Cylinder Assembly LH


Use tags or make a memo to identify the places to reconnect the brake lines.


d.
C426223

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




e.
C425431

Using a union nut wrench, disconnect the front brake tube while holding the front flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the front brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the front brake tube from the connecting parts.




f.
C426261

Disengage the clamp and separate the front brake tube.

NOTICE:

Do not kink or damage the front brake tube.



g.
C426262

Move aside the front brake tube as shown in the illustration.

NOTICE:

Do not apply excessive force to the front brake tube.



h.
C426263

Disengage the clamp and remove the brake tube clamp.


i.
C426224

Remove the 2 bolts, nut and brake actuator with bracket.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator with bracket by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



Hide 44510 11.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C425437

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44521B 12.REMOVE NO. 2 BRAKE ACTUATOR CASE COLLAR

HINT:

Perform this procedure only when replacement of the No. 2 brake actuator case collars is necessary.


a.
C425438

Remove the 3 nuts.


b.

Remove the 3 No. 2 brake actuator case collars from the brake actuator bracket cushion.


Hide 44547B 13.REMOVE BRAKE ACTUATOR BRACKET CUSHION

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.


a.
C425439

Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.