Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for HV Model LHD)
RM37A0E _54 Brake _086869 BRAKE SYSTEM (OTHER) _0420924 BRAKE BOOSTER(for HV Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for HV Model LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of brake booster with master cylinder assembly
1.

Bleed air

2.

Perform "Calibration"


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·
C426238C01
0.344,1.688 0.781,1.521 false 2.771,1.271 3.031,1.458 3.031,1.458 2.573,1.292 true 2.823,0.521 3.042,0.333 false 0.198,0.969 0.313,0.75 false 2.344,1.844 2.781,1.917 false 0.594,0.573 0.26,0.302 false 1.24,0.25 0.885,0.177 false 2.135,0.302 2.469,0.188 false 0.188,1.604 0.531,1.792 0.344,0.188 10 false *1 3.063,1.385 3.365,1.667 0.302,0.281 10 false *2 0.115,0.979 0.448,1.302 0.333,0.323 10 false *3 0.104,0.219 0.427,0.49 0.323,0.271 10 false *4 3.073,0.24 3.406,0.5 0.333,0.26 10 false *5 2.823,1.844 3.208,2.052 0.385,0.208 10 false *6 0.729,0.094 1.083,0.333 0.354,0.24 10 false *7 2.5,0.104 2.854,0.344 0.354,0.24 10 false *8
*1 No. 1 Skid Control ECU
*2 Reservoir Hose
*3 Master Cylinder Push Rod Clevis
*4 Boot
*5 Reservoir
*6 No. 1 Brake Actuator Tube
*7 No. 1 Wire Clamp Bracket
*8 Brake Booster with Accumulator Pump Assembly


Do not carry the brake master cylinder with pump assembly by the parts shown in the illustration.



PROCEDURE

Hide 1.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

a.

Using the GTS, perform the accumulator pressure zero down operation.

i.

Select "Motor Deactivate" on the "ECB Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 2617

ii.

Perform "Motor Deactivate" according to the display on the GTS.


iii.

Select "ECB Deactivate" on the "ECB Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 2617

iv.

Perform "ECB Deactivate" according to the display on the GTS.


v.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.



vi.

Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.



vii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL



b.

When the accumulator pressure zero down could not be performed using the GTS.

NOTICE:

If DTCs are output, the accumulator pressure zero down operation may not be complete. In this case, perform the following procedure.


i.
C426232

With the ignition switch off, disconnect the brake booster with master cylinder assembly connector.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



ii.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


iii.

Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.



iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL



Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53808A 3.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 4.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 5.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 6.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 7.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 8.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 55704B 9.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 11.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 82111 12.DISCONNECT ENGINE ROOM MAIN WIRE

a.
C426232

Disconnect the connector from the brake master cylinder with pump assembly.


b.
C426233C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake master cylinder with pump assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



c.

Disengage the clamp to separate the engine room main wire from the brake master cylinder with pump assembly.


d.
C425746

Remove the bolt to separate the engine room main wire from the vehicle body.


Hide 13.DISCONNECT RESERVOIR HOSE

a.
C426234

Slide the 2 clips and disconnect the 2 reservoir hoses from the brake master cylinder with pump assembly.


Hide 14.DISCONNECT BRAKE LINE

a.
C426235

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder with pump assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




Hide 67914 15.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112A 16.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 55606 17.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 53601 18.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55045 19.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 55446A 20.REMOVE NO. 1 SWITCH HOLE BASE

Hide 73900 21.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 84340 22.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 47101A 23.REMOVE BRAKE PEDAL RETURN SPRING

a.
C426256

Remove the brake pedal return spring from the brake pedal support assembly.


Hide 47264A 24.REMOVE PUSH ROD PIN

a.
C426236

Remove the clip and push rod pin.


Hide 25.REMOVE BRAKE MASTER CYLINDER WITH PUMP ASSEMBLY

a.
C426237

Remove the 4 nuts and brake master cylinder with pump assembly.

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Be careful not to allow any brake fluid to enter the connector.




Hide 44785 26.REMOVE BRAKE BOOSTER GASKET

Hide 47235G 27.REMOVE NO. 2 RESERVOIR HOSE

a.
C426239

Slide the 2 clips and remove the No. 2 reservoir hose.


Hide 47234L 28.REMOVE NO. 1 RESERVOIR HOSE

a.
C426241

Slide the 2 clips and remove the No. 1 reservoir hose.


Hide 44551C 29.REMOVE NO. 1 BRAKE ACTUATOR TUBE

a.
C426243

Using a union nut wrench, remove the No. 1 brake actuator tube.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




Hide 47070B 30.REMOVE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

Hide 31.REMOVE NO. 1 WIRE CLAMP BRACKET

a.
C426247

Using a 5 mm long hexagon socket wrench, remove the bolt and No. 1 wire clamp bracket.


Hide 32.REMOVE NO. 2 WIRE CLAMP BRACKET

a.
C426248

Using a 5 mm long hexagon socket wrench, remove the bolt and No. 2 wire clamp bracket.


Hide 47943 33.REMOVE NO. 3 BRAKE POWER SUPPLY BRACKET

a.
C425445

Using a 5 mm long hexagon socket wrench, remove the 2 bolts and No. 3 brake power supply bracket.


Hide 47942 34.REMOVE NO. 2 BRAKE POWER SUPPLY BRACKET

a.
C426249

Using a 5 mm long hexagon socket wrench, remove the 2 bolts and No. 2 brake power supply bracket.