The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
2.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
3.REMOVE FRONT WHEEL RH
53736
4.REMOVE FRONT FENDER APRON SEAL RH
5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
53808A
6.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH
53807A
7.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH
Perform the same procedure as for the LH side.
53892C
8.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT LH
53891C
9.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT RH
Perform the same procedure as for the LH side.
10.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH
53607B
11.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
55704B
12.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY
13.REMOVE BRAKE ACTUATOR WITH BRACKET
|
Release the lock lever |
|
Disconnect the connector |
Release the lock lever and disconnect the connector from the brake actuator assembly.
Be careful not to allow any brake fluid to enter the connector.
Remove the 2 bolts to separate the brake lines.
| *a | From 1st Chamber of Brake Master Cylinder Sub-assembly |
| *b | From 2nd Chamber of Brake Master Cylinder Sub-assembly |
| *c | To Front Wheel Cylinder Assembly RH |
| *d | To Rear Wheel Cylinder Assembly LH |
| *e | To Rear Wheel Cylinder Assembly RH |
| *f | To Front Wheel Cylinder Assembly LH |
Use tags or make a memo to identify the places to reconnect the brake lines.
Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Using a union nut wrench, disconnect the front brake tube while holding the front flexible hose with a wrench.
Do not kink or damage the front brake tube.
Do not allow any foreign matter such as dirt or dust to enter the front brake tube from the connecting parts.
Disengage the clamp and separate the front brake tube.
Do not kink or damage the front brake tube.
Move aside the front brake tube as shown in the illustration.
Do not apply excessive force to the front brake tube.
Disengage the clamp and remove the brake tube clamp.
| *a | Protective Tape |
Apply protective tape to the vehicle body as shown in the illustration.
Remove the 2 bolts.
Insert the tool from the bottom of the vehicle.
Remove the nut and brake actuator with bracket.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Be careful not to allow any brake fluid to enter the connector.
Do not hold the brake actuator with bracket by the connector.
Do not drop the brake actuator with bracket when carrying it.
Remove the brake actuator with bracket while avoiding the brake lines.
44510
14.REMOVE BRAKE ACTUATOR ASSEMBLY
Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.
Do not hold the brake actuator assembly by the connector.
Do not drop the brake actuator assembly when carrying it.
44521B
15.REMOVE NO. 2 BRAKE ACTUATOR CASE COLLAR
Perform this procedure only when replacement of the No. 2 brake actuator case collars is necessary.
Remove the 3 nuts.
Remove the 3 No. 2 brake actuator case collars from the brake actuator bracket cushion.
44547B
16.REMOVE BRAKE ACTUATOR BRACKET CUSHION
Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.
Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.