Refer to DTC C050C12.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C050C23 | Left Rear Wheel Speed Sensor Signal Stuck Low | Any of the following is detected:
·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the skid control sensors is less than that from the other sensors for 30 seconds or more. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the skid control sensors is 0 km/h (0 mph) for 1 second or more. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both skid control sensors are 0 km/h (0 mph) for 30 seconds or more. |
·
Rear skid control sensor LH ·
Rear skid control sensor installation ·
Skid control sensor wire LH (No. 2 parking brake wire assembly) ·
Wire harness and connector ·
Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) |
Refer to DTC C050C12.
After replacing or removing and installing a skid control sensor, perform Dealer Mode (Signal Check) inspection to confirm that the skid control sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the skid control sensors are operating correctly.
| *1 | Rear Skid Control Sensor LH |
| *a | Correct |
| *b | Incorrect |
| *c | 8.5 N*m (87 kgf*cm, 75 in.*lbf) |
| *d | No clearance |
Check the rear skid control sensor LH installation.
There is no clearance between the rear skid control sensor LH and the rear axle carrier LH.
The installation bolt is tightened properly.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear skid control sensor LH.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for 4WD/AWD)>REMOVAL
Check the rear skid control sensor tip LH.
The rear skid control sensor tip LH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the rear skid control sensor LH, clean the rear skid control sensor LH.
If the rear skid control sensor LH is damaged, replace the rear skid control sensor LH with a new one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Start the engine.
Perform a road test.
Check the rear skid control sensor LH output value.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RL Wheel Speed | Rear skid control sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| RL Wheel Speed |
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of skid control sensor wire LH (No. 2 parking brake wire assembly) |
| *b | Front view of wire harness connector
(to Sensor Side Connector) |
| *c | Front view of wire harness connector
(to Vehicle Side Connector) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the u4 and uM2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| u4-2 (+) - uM2-3 (RL+) | Always | Below 1 Ω |
| u4-2 (+) or uM2-3 (RL+) - Body ground and other terminals | Always | 10 kΩ or higher |
| u4-1 (-) - uM2-4 (RL-) | Always | Below 1 Ω |
| u4-1 (-) or uM2-4 (RL-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM2-3 (RL+) - A39-5 (RL+) | Always | Below 1 Ω |
| uM2-3 (RL+) or A39-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| uM2-4 (RL-) - A39-4 (RL-) | Always | Below 1 Ω |
| uM2-4 (RL-) or A39-4 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the component with the rear speed sensor rotor LH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for 4WD/AWD)>REMOVAL
Check the rear speed sensor rotor LH.
The rear speed sensor rotor LH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the rear speed sensor rotor LH, clean the rear speed sensor rotor LH.
Do not use parts cleaner when cleaning the rear speed sensor rotor LH.
If the rear speed sensor rotor LH is damaged, replace the rear speed sensor rotor LH with a new one.
The rear speed sensor rotor LH is incorporated into the rear axle hub and bearing assembly LH.
If the rear speed sensor rotor LH needs to be replaced, replace it together with the rear axle hub and bearing assembly LH.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The rear speed sensor rotor LH is damaged.) | B |
| NG (There is foreign matter on the rear speed sensor rotor LH.) | C |
A
B
C