Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB (for 4WD/AWD)
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0417448 REAR AXLE HUB(for 4WD/AWD) A

AXLE AND DIFFERENTIAL  REAR AXLE HUB(for 4WD/AWD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub and bearing assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:
for HV Model
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.DISABLE BRAKE CONTROL (for HV Model)

Hide 2.REMOVE REAR WHEEL

Hide 48738 3.REMOVE REAR SUSPENSION ARM COVER

Hide 42312B 4.REMOVE REAR AXLE SHAFT NUT

a.
C424675N01
2.406,1.167 2.594,0.979 2.594,0.979 2.865,0.979 false 2.958,0.906 3.375,1.104 0.417,0.198 10 false SST

Using SST and a hammer, release the staked part of the rear axle shaft nut.

SST
09930-00010  

NOTICE:

Loosen the staked part of the rear axle shaft nut completely, otherwise the threads of the rear drive shaft assembly may be damaged.



b.

While applying the brakes, using a 30 mm deep socket wrench, remove the rear axle shaft nut.


Hide 890C0A 5.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C426038

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




b.
C424674C01
1.281,0.969 1.729,0.969 true 1.021,0.885 1.25,1.063 0.229,0.177 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear skid control sensor.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.

·

Be careful not to damage the rear skid control sensor or connector cover.




Hide 89544E 6.REMOVE REAR SKID CONTROL SENSOR

a.
C424666

Remove the bolt and the rear skid control sensor from the rear axle carrier sub-assembly.

NOTICE:
·

Keep the tip of the rear skid control sensor and installation hole free of foreign matter.

·

Do not rotate or apply excessive force to the rear skid control sensor when removing it from the rear axle carrier sub-assembly. Rotating or applying excessive force may result in damage to the rear skid control sensor.




Hide 47850 7.SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY

Hide 8.REMOVE REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD

Hide 42431 9.REMOVE REAR DISC

Hide 42450B 10.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

a.
C424677C01
2.323,1.625 2.323,0.729 2.323,0.729 2.698,0.729 true 2.333,0.99 2.719,0.99 true 2.26,1.656 2.573,1.833 0.313,0.177 10 false *a
*a Matchmark


Put matchmarks on the rear drive shaft assembly and rear axle hub and bearing assembly.


b.
C424678

Using a plastic hammer, separate the rear drive shaft assembly from the rear axle hub and bearing assembly.

HINT:

If it is difficult to separate the rear drive shaft assembly from the rear axle hub and bearing assembly, tap the end of the rear drive shaft assembly using a brass bar and a hammer.



c.
C424679

Remove the 4 bolts, rear axle hub and bearing assembly and rear disc brake dust cover sub-assembly from the rear axle carrier sub-assembly.