The skid control sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each skid control sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).
When the connectors between the skid control sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C051212 | Right Rear Wheel Speed Sensor Circuit Short to Battery | The skid control sensor short signal is ON continuously for 0.5 seconds or more. | ·
Rear skid control sensor RH ·
Skid control sensor wire RH (No. 1 parking brake wire assembly) ·
Wire harness and connector ·
Skid control ECU (brake actuator assembly) |
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
After replacing or removing and installing a skid control sensor, perform Dealer Mode (Signal Check) inspection to confirm that the skid control sensors are operating correctly.
| *a | Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
(to Rear Skid Control Sensor RH) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the u3 rear skid control sensor RH connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| u3-1 (+) - u3-2 (-) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the uM1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM1-3 (RR+) - uM1-4 (RR-) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM1-4 (RR-) - Body ground | Always | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM1-3 (RR+) or A39-20 (RR+) - uM1-4 (RR-) or A39-19 (RR-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
NG