The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.
If a communication error with the yaw rate and acceleration sensor (airbag sensor assembly) is detected, DTCs U012587 and/or U015187 are stored.
If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.
These DTCs are also output when the calibration has not been completed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C051D54 | Multi-axis Acceleration Sensor Module "A" Missing Calibration | Zero point calibration of acceleration sensor (airbag sensor assembly) undone. | ·
Acceleration sensor (airbag sensor assembly) zero point not calibrated ·
Acceleration sensor (airbag sensor assembly) installation ·
Acceleration sensor (airbag sensor assembly) ·
Skid control ECU (brake actuator assembly) |
| C121054 | Yaw Rate Sensor Missing Calibration | Zero point calibration of yaw rate sensor (airbag sensor assembly) undone. | ·
Yaw rate sensor (airbag sensor assembly) zero point not calibrated ·
Yaw rate sensor (airbag sensor assembly) installation ·
Yaw rate sensor (airbag sensor assembly) ·
Skid control ECU (brake actuator assembly) |
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform "Calibration" after performing "Reset Memory".
Perform calibration.
| Tester Display |
|---|
| Calibration |
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C051D54 and C121054 are not output. | A |
| DTCs C051D54 and/or C121054 are output. | B |
A
B
Turn the ignition switch off.
Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.
The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Lateral G | Lateral G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
| Yaw Rate Sensor Value | Yaw rate sensor (airbag sensor assembly) | Min.: -128°/s
Max.: 127°/s |
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Tester Display |
|---|
| Lateral G |
| Forward and Rearward G |
| Yaw Rate Sensor Value |
The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
NG