Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C052C13  ABS Pump Motor Control Circuit Open  C052C49  ABS Pump Motor Control Internal Electronic Failure  C052F14  ABS Pump Motor Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

The motor relay and motor fail safe relay are built into the brake actuator assembly.

When the skid control ECU (brake actuator assembly) operates ABS, TRC, VSC, brake assist, etc., the motor relay turns ON and drives the motor pump built into the brake actuator assembly.

If any DTCs related to motor supply power are stored, fail-safe is performed and supply of power to the motor relay is cut by the motor fail safe relay.

If the voltage supplied to the motor relay (BM) is below the DTC detection threshold due to low voltage from the auxiliary battery or alternator, these DTCs may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C052C13 ABS Pump Motor Control Circuit Open Either of the following is detected:
·

When the +BS terminal voltage is from 9.5 to 17.4 V with the motor relay ON while control operates, a relay contact OFF condition continues for 0.12 seconds or more.

·

When the +BS terminal voltage is from 9.5 to 17.4 V, a motor relay supervision voltage malfunction continues for 0.12 seconds or more when the motor relay turns ON during control operation.


·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


C052C49 ABS Pump Motor Control Internal Electronic Failure Any of the following is detected:
·

When the +BS terminal voltage is from 9.5 to 17.4 V, overcurrent in the motor relay and motor fail-safe relay continues for 0.05 seconds or more.

·

Motor relay overcurrent continues for 0.05 seconds or more.

·

When the +BS terminal voltage is from 9.5 to 17.4 V, a motor relay gate voltage malfunction continues for 0.12 seconds or more.


·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


C052F14 ABS Pump Motor Supply Voltage Circuit Short to Ground or Open When voltage at +BS terminal is 9.5 V or higher, open in BM terminal continues for 1 second or more.
·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C322755E12
0.313,1.333 1.167,2.01 0.854,0.677 10 false from Auxiliary Battery 1.781,1.542 2.688,1.792 0.906,0.25 10 false ABS NO. 1 4.76,2.208 6.302,2.458 1.542,0.25 10 false Skid Control ECU 4.646,1.281 6.573,1.604 1.927,0.323 10 false Motor Fail-safe Relay 4.979,3.302 5.896,3.542 0.917,0.24 10 false Motor Relay 5.094,4.438 6.01,4.677 0.917,0.24 10 false Pump Motor 4.49,5.031 6.438,5.354 1.948,0.323 10 false Brake Actuator Assembly 4.49,4.865 4.875,5.073 0.385,0.208 10 false A39 3.667,2.854 4.229,3.073 0.563,0.219 10 false GND2 3.677,1.25 4.24,1.469 0.563,0.219 10 false BM 3.396,1.25 3.625,1.469 0.229,0.219 10 false 46 3.406,2.854 3.635,3.073 0.229,0.219 10 false 30 1.813,1.26 2.042,1.479 0.229,0.219 10 false 1 2.26,1.25 2.49,1.469 0.229,0.219 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BM TERMINAL)
a.
C343081C57
1.49,0.146 1.854,0.406 0.365,0.26 2.896,1.823 2.646,1.292 true 1.542,0.198 2,0.396 0.458,0.198 10 false A39 0.167,0.188 0.625,0.385 0.458,0.198 10 false *a 2.833,1.854 3.292,2.052 0.458,0.198 10 false BM
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-46 (BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-30 (GND2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Reconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
DTCs C052C13, C052C49 and C052F14 are not output. A
DTCs C052C13, C052C49 and/or C052F14 are output. B


HINT:
·

If a speed signal of 20 km/h (12 mph) or more is sent to the skid control ECU (brake actuator assembly) with the ignition switch turned to ON and the stop light switch assembly off, the ECU performs self diagnosis of the motor circuit.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B