Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C054016  Brake Pressure Sensor "A" Circuit Voltage Below Threshold  C05401C  Brake Pressure Sensor "A" Circuit Voltage Out of Range  C05401F  Brake Pressure Sensor "A" Circuit Intermittent  C054029  Brake Pressure Sensor "A" Signal Invalid  C05402A  Brake Pressure Sensor "A" Signal Stuck In Range  C054031  Brake Pressure Sensor "A" No Signal  C054049  Brake Pressure Sensor "A" Internal Electronic Failure  C054096  Brake Pressure Sensor "A" Component Internal Failure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C054016 Brake Pressure Sensor "A" Circuit Voltage Below Threshold Master cylinder pressure is below -0.744 MPa (-7.6 kgf/cm2, -107 psi) for 5 seconds or more. Skid control ECU (brake actuator assembly)
C05401C Brake Pressure Sensor "A" Circuit Voltage Out of Range When vehicle speed is 7 km/h (4.3 mph) or more, braking is performed (stop light switch assembly is ON) and master cylinder pressure differential value is below 20 MPa/s, difference between master cylinder pressure estimated from vehicle deceleration and master cylinder pressure sensor input value is large for 1 second or more 5 times or more for 9 trips. Skid control ECU (brake actuator assembly)
C05401F Brake Pressure Sensor "A" Circuit Intermittent When vehicle speed is 10 km/h (6 mph) or more, noise in master cylinder pressure value occurs 7 times or more in 5 seconds. Skid control ECU (brake actuator assembly)
C054029 Brake Pressure Sensor "A" Signal Invalid Master cylinder pressure sensor invalid condition continues for 0.2 seconds or more. Skid control ECU (brake actuator assembly)
C05402A Brake Pressure Sensor "A" Signal Stuck In Range Any of the following is detected:
·

When vehicle speed is 7 km/h (4.3 mph) or more and master cylinder pressure exceeds 1.764 MPa (18.0 kgf/cm2, 255 psi), master cylinder pressure does not increase 0.048 MPa (0.5 kgf/cm2, 6.9 psi) or more continuously for 60 seconds.

·

When vehicle speed is 7 km/h (4.3 mph) and master cylinder pressure is 2.45 MPa (25.0 kgf/ cm2, 355 psi) or more, master cylinder pressure does not increase 0.048 MPa (0.5 kgf/cm2, 6.9 psi) or more continuously for 30 seconds.

·

Master cylinder pressure does not increase 0.048 MPa (0.5 kgf/cm2, 6.9 psi) or more 5 times or more while vehicle speed decreases from 40 km/h (25 mph) to 0 km/h (0 mph).


Skid control ECU (brake actuator assembly)
C054031 Brake Pressure Sensor "A" No Signal Master cylinder pressure sensor communication invalid condition continues for 0.1 seconds or more. Skid control ECU (brake actuator assembly)
C054049 Brake Pressure Sensor "A" Internal Electronic Failure Either of the following is detected:
·

When voltage at terminal +BS is 9.5 V or higher, power supply voltage of master cylinder pressure sensor is continuously low for 1 second or more.

·

When master cylinder pressure sensor power supply voltage has risen, master cylinder pressure sensor has overheated or overcurrent of master cylinder pressure sensor continues for 1.2 seconds or more.


Skid control ECU (brake actuator assembly)
C054096 Brake Pressure Sensor "A" Component Internal Failure Either of the following is detected:
·

Master cylinder pressure exceeds 23.328 MPa (237.8 kgf/cm2, 3382 psi) continuously for 0.1 seconds.

·

Master cylinder temperature exceeds 150°C (302°F) continuously for 0.1 seconds.


Skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY

NEXT

END