Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C137BA2  Brake System Control Module "A" System Voltage System Voltage Low  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits operation of ABS, brake assist, etc.

This DTC is stored when the +BS terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the auxiliary battery or alternator circuit, etc.

The DTC is cleared when the +BS terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C137BA2 Brake System Control Module "A" System Voltage System Voltage Low Any of the following is detected:
·

When the +BS terminal voltage is below 9.5 V, the power source voltage for all speed sensors is continuously low for 60 seconds or more.

·

After the +BS terminal voltage is below 9.5 V continuously for 3 seconds or more, the +BS terminal voltage is below 9.5 V continuously for 7 seconds or more at a vehicle speed exceeding 3 km/h (2 mph).

·

When the +BS terminal voltage is 9.5 V or higher and the vehicle speed exceeds 15 km/h (9 mph), the IG1 terminal voltage is 10 V or less continuously for 60 seconds or more.

·

When the +BS terminal voltage is below 9.5 V and the solenoid relay is ON, the relay contact is OFF continuously for 1.22 seconds or more.

·

When the +BS terminal voltage is below 9.5 V, motor fail-safe relay overcurrent continues for 1.05 seconds or more.


·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C408683E19
1.385,1.146 3.063,1.427 1.677,0.281 10 false from Auxiliary Battery 3.708,1.333 4.833,1.615 1.125,0.281 10 false ABS NO. 2 5.667,1.031 5.979,1.229 0.313,0.198 10 false 14 5.74,2.813 6.052,3.01 0.313,0.198 10 false 1 5.969,1.156 6.385,1.396 0.417,0.24 10 false +BS 5.969,2.938 6.385,3.177 0.417,0.24 10 false GND1 4.26,3.875 4.719,4.073 0.458,0.198 10 false A39 4.25,4.042 7.156,4.406 2.906,0.365 10 false Skid Control ECU (Brake Actuator Assembly) 3.719,1.021 3.875,1.219 0.156,0.198 10 false 1 4.208,1.031 4.365,1.229 0.156,0.198 10 false 2 1.854,2.042 2.979,2.323 1.125,0.281 10 false from IG Circuit 4.188,1.906 4.344,2.104 0.156,0.198 10 false 2 3.719,1.917 3.875,2.115 0.156,0.198 10 false 1 5.708,1.917 6.021,2.115 0.313,0.198 10 false 45 5.969,2.042 6.385,2.281 0.417,0.24 10 false IG1 3.542,2.229 5.031,2.583 1.49,0.354 10 false ECU-IG1 NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the auxiliary battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.
C343081C60
1.49,0.146 1.854,0.406 0.365,0.26 2.896,1.823 2.646,0.979 true 1.542,0.198 2,0.396 0.458,0.198 10 false A39 0.167,0.188 0.625,0.385 0.458,0.198 10 false *a 2.792,1.865 3.25,2.063 0.458,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-14 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C343081C61
1.49,0.146 1.854,0.406 0.365,0.26 2.594,1.771 2.385,1.354 true 1.542,0.188 2,0.385 0.458,0.198 10 false A39 0.167,0.188 0.625,0.385 0.458,0.198 10 false *a 2.563,1.802 3.021,2 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-45 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-1 (GND1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Reconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C137BA2 is not output. A
DTC C137BA2 is output. B



A

B