Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C14FE14  Steering Angle Sensor Supply Voltage Circuit Circuit Short to Ground or Open  


DESCRIPTION

This DTC is stored when the skid control ECU (brake actuator assembly) receives a power supply malfunction signal from the steering angle sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C14FE14 Steering Angle Sensor Supply Voltage Circuit Circuit Short to Ground or Open When the +BS terminal voltage is from 9.5 to 17.4 V, a steering angle sensor power supply malfunction signal is received from the steering angle sensor.
·

Steering angle sensor

·

Wire harness and connector



CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C14FE14 is not output. A
DTC C14FE14 is output. B



A

B

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C418963C01
0.333,1.167 0.75,1.417 0.417,0.25 1.896,1.594 2.177,1.927 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 0.417,1.198 0.802,1.469 0.385,0.271 10 false H57 2.229,1.917 2.688,2.115 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Steering Angle Sensor)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the H57 steering angle sensor connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H57-9 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)
a.
C418963C02
0.333,1.167 0.75,1.417 0.417,0.25 1.917,1.24 2.177,0.5 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 0.417,1.188 0.802,1.458 0.385,0.271 10 false H57 2.104,0.313 2.563,0.51 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the ignition switch off.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H57-4 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H57-6 (ESS) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR