Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086873 PARKING BRAKE _0420958 ELECTRIC PARKING BRAKE SYSTEM(for HV Model) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for HV Model)  C060E19  Left Electric Parking Brake Actuator Circuit Current Above Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C060E19 Left Electric Parking Brake Actuator Circuit Current Above Threshold When the electric parking brake is operating, overcurrent is detected in the parking brake actuator assembly LH 3 times.
·

Parking brake actuator assembly LH

·

No. 2 parking brake wire assembly

·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

CAUTION / NOTICE / HINT

NOTICE:
·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.



PROCEDURE

1.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the uM2 and u2 No. 2 parking brake wire assembly connectors.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

C427097C01
1.792,0.25 2.208,0.5 0.417,0.25 5,0.25 5.417,0.5 0.417,0.25 5.917,2.083 5.448,1.667 false 4.5,2.083 4.99,1.667 false 1.875,0.292 2.333,0.49 0.458,0.198 10 false uM2 5.135,0.292 5.594,0.49 0.458,0.198 10 false u2 5.948,2.083 6.365,2.333 0.417,0.25 10 false + 4.427,2.073 4.885,2.271 0.458,0.198 10 false - 1.917,2.375 2.375,2.583 0.458,0.208 10 false *b 0.125,0.125 0.656,0.365 0.531,0.24 10 false *a 5.146,2.385 5.604,2.583 0.458,0.198 10 false *c
*a Front view of No. 2 Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly LH) - -


Standard Resistance:
Tester Connection Condition Specified Condition
uM2-1 - u2-2 (+) Always Below 1 Ω
uM2-1 or u2-2 (+) - Body ground and other terminals Always 10 kΩ or higher
uM2-2 - u2-1 (-) Always Below 1 Ω
uM2-2 or u2-1 (-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)
a.

Make sure the No. 2 parking brake wire assembly is securely installed.


b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the u2 parking brake actuator assembly LH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-3 (MRL+) - u2-2 (+) Always Below 1 Ω
A57-3 (MRL+) or u2-2 (+) - Body ground Always 10 kΩ or higher
A57-2 (MRL-) - u2-1 (-) Always Below 1 Ω
A57-2 (MRL-) or u2-1 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH
a.

Remove the parking brake actuator assembly LH.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


b.

Inspect the parking brake actuator assembly LH.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO +B

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

4.CHECK FOR SHORT TO +B
a.

Make sure the No. 2 parking brake wire assembly is securely installed.


b.

Disconnect the u2 parking brake actuator assembly LH connector.


c.
C401220C27
1.5,0.333 1.917,0.583 0.417,0.25 2.25,2.667 1.99,2 false 1.167,2.667 1.438,2 false 0.25,0.229 0.563,0.427 0.313,0.198 10 false *a 1.635,0.375 1.948,0.573 0.313,0.198 10 false u2 1.094,2.656 1.76,2.865 0.667,0.208 10 false - 2.26,2.667 2.75,2.865 0.49,0.198 10 false +
*a Front view of No. 2 Parking Brake Wire Assembly
(to Parking Brake Actuator Assembly LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
u2-2 (+) - u2-1 (-) Electric parking brake not operating Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

NG

5.CHECK FOR SHORT TO +B
5.CHECK FOR SHORT TO +B
a.

Disconnect the uM2 No. 2 parking brake wire assembly connector.


b.
C427098C02
1.5,0.417 1.917,0.667 0.417,0.25 0.25,0.25 0.583,0.5 0.333,0.25 10 false *a 1.594,0.469 1.896,0.698 0.302,0.229 10 false uM2
*a Front view of wire harness connector
(to No. 2 Parking Brake Wire Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
uM2-1 - uM2-2 Electric parking brake not operating Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

6.CHECK FOR SHORT TO +B
6.CHECK FOR SHORT TO +B
a.

Disconnect the uM2 No. 2 parking brake wire assembly connector.


b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

C427099C01
1.781,0.417 2.198,0.667 0.417,0.25 5.125,0.417 5.542,0.667 0.417,0.25 2.083,2.167 1.5,1.375 true 0.688,2.167 1.271,1.375 true 1.885,0.458 2.344,0.656 0.458,0.198 10 false A57 5.219,0.458 5.677,0.656 0.458,0.198 10 false uM2 0.5,0.75 0.958,1.031 0.458,0.281 10 false *b 0.167,0.167 0.583,0.417 0.417,0.25 10 false *a 4.583,0.75 5.125,0.948 0.542,0.198 10 false *c 0.542,2.198 1.042,2.448 0.5,0.25 10 false MRL- 1.948,2.198 2.448,2.448 0.5,0.25 10 false MRL+
*a Front view of wire harness connector *b (to No. 2 Skid Control ECU (Brake Actuator Assembly))
*c (to No. 2 Parking Brake Wire Assembly) - -


Standard Voltage:
Tester Connection Condition Specified Condition
uM2-1 or A57-3 (MRL+) - Body ground Always Below 1 V
uM2-2 or A57-2 (MRL-) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR