| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C061014 | Right Electric Parking Brake Actuator Control Circuit Short to Ground or Open | ·
Diagnosis Condition: Ignition switch ON ·
Malfunction Status: When the ECU power supply is normal, a malfunction in the electric parking brake actuator RH internal circuit is detected. ·
Detection Time: Approximately 1 second |
·
Parking brake actuator assembly RH ·
No. 1 parking brake wire assembly ·
Wire harness and connector ·
No. 2 skid control ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the No. 2 skid control ECU (brake actuator assembly), perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".
When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the uM1 and u1 No. 1 parking brake wire assembly connectors.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of No. 1 Parking Brake Wire Assembly | *b | (to wire harness connector) |
| *c | (to Parking Brake Actuator Assembly RH) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM1-1 - u1-2 (+) | Always | Below 1 Ω |
| uM1-1 or u1-2 (+) - Body ground and other terminals | Always | 10 kΩ or higher |
| uM1-2 - u1-1 (-) | Always | Below 1 Ω |
| uM1-2 or u1-1 (-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure the No. 1 parking brake wire assembly is securely installed.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Disconnect the u1 parking brake actuator assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A57-13 (MRR+) - u1-2 (+) | Always | Below 1 Ω |
| A57-13 (MRR+) or u1-2 (+) - Body ground | Always | 10 kΩ or higher |
| A57-12 (MRR-) - u1-1 (-) | Always | Below 1 Ω |
| A57-12 (MRR-) or u1-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking brake actuator assembly RH.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
Inspect the parking brake actuator assembly RH.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG