| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C06132A | Right Electric Parking Brake Actuator Signal Stuck In Range | ·
Diagnosis Condition: Electric parking brake operating ·
Malfunction Status: Motor locked, gear locked, free spinning ·
Detection Time: - |
·
Parking brake actuator assembly RH ·
No. 1 parking brake wire assembly ·
Wire harness or connector ·
Rear brake RH |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Electric parking brake operating | ○ | ○ | ○ |
| Malfunction Status | Motor lock detected | ○ | - | - |
| Gear lock detected | - | ○ | - | |
| Free spinning detected | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
Although DTC C06132A may be stored after entering pad replacement mode, this is not a malfunction.
Although DTC C06132A may be stored after forcibly releasing the parking brake, this is not a malfunction.
To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the No. 2 skid control ECU (brake actuator assembly), perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".
When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.
Using the GTS, check for DTCs other than DTC C06132A.
| Result | Proceed to |
|---|---|
| Only DTC C06132A is output | A |
| DTCs other than C06132A are output | B |
A
B
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model)>DIAGNOSTIC TROUBLE CODE CHART
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the uM1 and u1 No. 1 parking brake wire assembly connectors.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of No. 1 Parking Brake Wire Assembly | *b | (to wire harness connector) |
| *c | (to Parking Brake Actuator Assembly RH) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM1-1 - u1-2 (+) | Always | Below 1 Ω |
| uM1-1 or u1-2 (+) - Body ground and other terminals | Always | 10 kΩ or higher |
| uM1-2 - u1-1 (-) | Always | Below 1 Ω |
| uM1-2 or u1-1 (-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Make sure the No. 1 parking brake wire assembly is securely installed.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Disconnect the u1 parking brake actuator assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A57-13 (MRR+) - u1-2 (+) | Always | Below 1 Ω |
| A57-12 (MRR-) - u1-1 (-) | Always | Below 1 Ω |
| A57-13 (MRR+) or u1-2 (+) - Body ground | Always | 10 kΩ or higher |
| A57-12 (MRR-) or u1-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter rear brake pad replacement mode.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE
Turn the ignition switch off.
Check that the rotating parts are not seized or the actuator is not spinning freely.
Check that the parking brake actuator assembly RH is installed properly to the rear brake caliper and that it is not spinning freely.
For the parking brake actuator assembly RH removal procedure: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
Check that there is no damage to the rotating parts from the parking brake actuator assembly RH to the rear brake caliper.
Inspect the parking brake actuator assembly RH and check that it operates correctly.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION
Check that the rear brake caliper threaded part rotates and that the rear disc brake piston moves outward.
For the check procedures, refer to the parking brake forced release method when not using the GTS.
Click hereBrake>PARKING BRAKE>FORCED RELEASE>OPERATION METHOD
Return to normal mode after work is complete.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE
| Result | Proceed to |
|---|---|
| Parking brake actuator assembly RH is malfunctioning | A |
| Other than parking brake actuator assembly RH is malfunctioning | B |
A
B