Home › Brake › PARKING BRAKE › FORCED RELEASE
RM37A0E _54 Brake _086873 PARKING BRAKE _0420907 FORCED RELEASE A

PARKING BRAKE  FORCED RELEASE  OPERATION METHOD  


CAUTION / NOTICE / HINT

CAUTION:
C426032

If work is performed without first securing the vehicle, the vehicle may start moving and cause a serious accident or other disaster. Therefore, be sure to use wheel chocks to secure the vehicle before performing work.


PROCEDURE

Hide 67914 2.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913 3.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62112A 4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 62111A 5.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 58441L 6.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 7. PARKING BRAKE FORCED RELEASE

CAUTION:

Work on a level surface to ensure safety.


NOTICE:
·

To release the parking brake, follow the procedure for when using SST.

·

If the parking brake cannot be released, follow the procedure for when not using SST.

·

When moving the vehicle after releasing the parking brake, install all parts and do not connect the 2 connectors shown in the illustration.

C426033

·

If the ignition switch is ON or the hybrid system or engine is started with the 2 connectors disconnected, a DTC may be stored. Clear any DTCs after performing work.

for HV Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model)>DTC CHECK / CLEAR

for Gasoline Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR



a.

When using SST:

i.

Park the vehicle on a level surface and move the shift lever to P.


ii.

Turn the ignition switch off and use wheel chocks to secure the vehicle.


iii.

Disconnect the 2 connectors shown in the illustration.

C426033


iv.

Connect SST (09756-48020) to SST (09756-48060).

SST
09756-48020  09756-48060  

for HV Model:
C426035C01
4.031,0.281 4.781,0.281 true 1.99,1.104 2.344,1.104 true 2.188,3.781 2.385,4.281 2.385,4.281 2.542,4.281 true 4.24,3.885 4.375,4.313 4.375,4.313 4.573,4.313 true 2.75,8.354 2.875,8.167 2.875,8.167 3.031,8.167 true 3.76,8.542 4.313,8.542 true 1.104,1.281 1.458,1.281 true 6.313,5.521 6.063,5.521 6.063,5.521 6.063,4.875 true 2.573,4.188 2.813,4.375 0.24,0.188 10 true *1 2.375,1.01 2.688,1.208 0.313,0.198 10 false *c 0.927,1.198 1.24,1.396 0.313,0.198 10 false *d 3.844,0.198 4.073,0.396 0.229,0.198 10 true *a 4.604,4.229 4.979,4.469 0.375,0.24 10 true SST 6.354,5.438 6.667,5.635 0.313,0.198 10 false *2 4.354,8.448 4.667,8.646 0.313,0.198 10 false *a 3.073,8.083 3.385,8.281 0.313,0.198 10 false *b
*1 Brake Pedal *2 Auxiliary Battery
*a SST (09756-48020) *b SST (09756-48060)
*c Release Button *d Finished Light
V100135

Connector - -


for Gasoline Model:
C426034C01
1.458,0.292 2.208,0.292 true 5.667,1.104 6.021,1.104 true 2.75,4.698 2.948,5.198 2.948,5.198 3.104,5.198 true 0.396,4.729 1.979,4.729 true 4.01,3.823 4.146,4.25 4.146,4.25 4.344,4.25 true 2.75,8.354 2.875,8.167 2.875,8.167 3.031,8.167 true 3.76,8.542 4.313,8.542 true 4.792,1.281 5.146,1.281 true 3.125,5.115 3.365,5.302 0.24,0.188 10 true *1 6.083,1.021 6.396,1.219 0.313,0.198 10 false *c 4.635,1.198 4.948,1.396 0.313,0.198 10 false *d 1.292,0.198 1.521,0.396 0.229,0.198 10 true *a 4.396,4.167 4.771,4.406 0.375,0.24 10 true SST 0.219,4.656 0.531,4.854 0.313,0.198 10 false *2 4.354,8.448 4.667,8.646 0.313,0.198 10 false *a 3.073,8.083 3.385,8.281 0.313,0.198 10 false *b
*1 Brake Pedal *2 Battery
*a SST (09756-48020) *b SST (09756-48060)
*c Release Button *d Finished Light
V100135

Connector - -



v.

Connect SST (09756-48060) to the 2 connectors.


vi.

Connect SST (09756-48020) to the auxiliary battery.


vii.

Push the release button on SST (09756-48020) with the brake pedal depressed.

CAUTION:

The vehicle may suddenly move when the parking brake is released. Make sure to perform the release operation with the brake pedal depressed.


HINT:
·

Confirm that the parking brake is operating by listening for operation sounds.

·

If no operation sounds are heard, push the release button on SST (09756-48020) with the brake pedal depressed.

·

The parking brake may not release if the auxiliary battery voltage is too low. In this case, perform the release operation again using a fully charged or new auxiliary battery.




viii.

When the finished light of SST (09756-48020) illuminates, release the brake pedal.


ix.

Move the vehicle forward and rearward to check that the parking brake is released.

CAUTION:

Be careful when performing this operation. The vehicle may suddenly move.


NOTICE:

When moving the vehicle after releasing the parking brake, check that the 2 connectors are disconnected.




b.

When not using SST:

NOTICE:

Perform the following procedure only when the parking brake cannot be released using SST.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



i.

Park the vehicle on a level surface and check that the shift lever is in P.


ii.

Turn the ignition switch off and use wheel chocks to secure the vehicle.


iii.

Check that the 2 connectors shown in the illustration have been disconnected.

C426033


iv.

Remove the rear wheel.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>REMOVAL

CAUTION:

When using a jack to lift the vehicle, make sure to support the vehicle using safety stands. Do not work on the vehicle with it supported only by a jack.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS



v.

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


vi.

Remove the parking brake actuator assembly from the rear disc brake cylinder assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


vii.
C426036

Insert an L-shaped T45 "TORX" wrench into the rear disc brake cylinder assembly.


viii.

Turn the L-shaped T45 "TORX" wrench 2 full rotations clockwise to release the parking brake lock.

NOTICE:

When moving the vehicle after releasing the parking brake, install all parts and do not connect the 2 connectors shown in the illustration.

C426033




Hide 58441L 8.INSTALL BATTERY SERVICE HOLE COVER (for HV Model)

Hide 62112A 9.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 62111A 10.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 67914 11.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 67913 12.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.