Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086873 PARKING BRAKE _0420958 ELECTRIC PARKING BRAKE SYSTEM(for HV Model) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for HV Model)  C123A14  Supply Voltage Circuit IG Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C123A14 Supply Voltage Circuit IG Open
·

Diagnosis Condition:

Ignition switch ON

·

Malfunction Status:

When the ECM is communicating via CAN communication, IG power is not input to the No. 2 skid control ECU (brake actuator sub-assembly).

·

Detection Time:

Approximately 15 seconds


·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

C427565E01
1.688,1.583 2.917,1.781 1.229,0.198 10 false ECU-IG2 NO. 3 4.188,1.427 4.625,1.667 0.438,0.24 10 false IG1 3.885,1.313 4.323,1.552 0.438,0.24 10 false 45 4.167,2.167 4.667,2.417 0.5,0.25 10 false A57 4.167,2.333 5.906,2.958 1.74,0.625 10 false No. 2 Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG TERMINAL VOLTAGE)
a.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.
C342413C22
1.458,0.125 1.875,0.375 0.417,0.25 2.5,1.823 2.365,1.354 true 1.552,0.167 2.01,0.365 0.458,0.198 10 false A57 2.458,1.844 2.917,2.042 0.458,0.198 10 false IG1 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-45 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR