Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086873 PARKING BRAKE _0420958 ELECTRIC PARKING BRAKE SYSTEM(for HV Model) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for HV Model)  C13B516  Electric Parking Brake Actuator Supply Voltage Circuit Voltage Below Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13B516 Electric Parking Brake Actuator Supply Voltage Circuit Voltage Below Threshold
·

Diagnosis Condition:

Ignition switch ON or electric parking brake switch assembly pulled to lock side with ignition switch off.

·

Malfunction Status:

Voltage at terminal +BS is less than 5.4 V*

·

Detection Time:

Approximately 0.5 seconds


HINT:

*: When the auxiliary battery voltage is 12 V.


·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions: C13B516
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ -
Electric parking brake switch assembly pulled to lock side with ignition switch off - ○
Malfunction Status Voltage at terminal +BS is less than 5.4 V*
HINT:

*: When the auxiliary battery voltage is 12 V.


○ ○
Detection Time Approximately 0.5 seconds Approximately 0.5 seconds
Number of Trips 1 trip 1 trip

HINT:

DTC will be stored when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C419806E05
1.813,1.583 3.042,1.781 1.229,0.198 10 false ABS NO. 2 4.188,1.427 4.625,1.667 0.438,0.24 10 false +BS 3.885,1.313 4.323,1.552 0.438,0.24 10 false 14 4.167,2.167 4.667,2.417 0.5,0.25 10 false A57 4.167,2.333 5.99,2.927 1.823,0.594 10 false No. 2 Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)
a.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


b.
C342413C23
1.458,0.125 1.875,0.375 0.417,0.25 2.969,1.813 2.698,0.99 true 1.552,0.167 2.01,0.365 0.458,0.198 10 false A57 2.896,1.854 3.354,2.052 0.458,0.198 10 false +BS 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-14 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR