Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086873 PARKING BRAKE _0420959 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model)  C061319  Right Electric Parking Brake Actuator Circuit Current Above Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C061319 Right Electric Parking Brake Actuator Circuit Current Above Threshold When the electric parking brake is operating, overcurrent is detected in the parking brake actuator assembly RH 3 times.
·

Parking brake actuator assembly RH

·

No. 1 parking brake wire assembly

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.



PROCEDURE

1.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the uM1 and u1 No. 1 parking brake wire assembly connectors.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

C427097C02
1.792,0.25 2.208,0.5 0.417,0.25 5,0.25 5.417,0.5 0.417,0.25 5.833,2.167 5.417,1.667 false 4.583,2.167 5,1.667 false 1.875,0.292 2.333,0.49 0.458,0.198 10 false uM1 5.135,0.292 5.594,0.49 0.458,0.198 10 false u1 5.875,2.156 6.292,2.406 0.417,0.25 10 false + 4.5,2.156 4.958,2.354 0.458,0.198 10 false - 1.917,2.375 2.375,2.583 0.458,0.208 10 false *b 0.125,0.125 0.656,0.365 0.531,0.24 10 false *a 5.146,2.385 5.604,2.583 0.458,0.198 10 false *c
*a Front view of No. 1 Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly RH) - -


Standard Resistance:
Tester Connection Condition Specified Condition
uM1-1 - u1-2 (+) Always Below 1 Ω
uM1-1 or u1-2 (+) - Body ground and other terminals Always 10 kΩ or higher
uM1-2 - u1-1 (-) Always Below 1 Ω
uM1-2 or u1-1 (-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)
a.

Make sure the No. 1 parking brake wire assembly is securely installed.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the u1 parking brake actuator assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-13 (MRR+) - u1-2 (+) Always Below 1 Ω
A39-13 (MRR+) or u1-2 (+) - Body ground Always 10 kΩ or higher
A39-12 (MRR-) - u1-1 (-) Always Below 1 Ω
A39-12 (MRR-) or u1-1 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH
a.

Remove the parking brake actuator assembly RH.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


b.

Inspect the parking brake actuator assembly RH.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO +B

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY RH

4.CHECK FOR SHORT TO +B
a.

Turn the ignition switch off.


b.

Make sure the No. 1 parking brake wire assembly is securely installed.


c.

Disconnect the u1 parking brake actuator assembly RH connector.


d.
C401220C28
1.5,0.333 1.917,0.583 0.417,0.25 2.25,2.667 2,2 false 1.167,2.667 1.417,2 false 0.25,0.25 0.583,0.583 0.333,0.333 10 false *a 1.646,0.375 1.958,0.573 0.313,0.198 10 false u1 1.083,2.656 1.75,2.865 0.667,0.208 10 false - 2.271,2.667 2.76,2.865 0.49,0.198 10 false +
*a Front view of No. 1 Parking Brake Wire Assembly
(to Parking Brake Actuator Assembly RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
u1-2 (+) - u1-1 (-) Electric parking brake not operating Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY RH

NG

5.CHECK FOR SHORT TO +B
5.CHECK FOR SHORT TO +B
a.

Disconnect the uM1 No. 1 parking brake wire assembly connector.


b.
C427098C03
1.5,0.417 1.917,0.667 0.417,0.25 0.25,0.25 0.552,0.5 0.302,0.25 10 false *a 1.594,0.458 1.896,0.688 0.302,0.229 10 false uM1
*a Front view of wire harness connector
(to No. 1 Parking Brake Wire Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
uM1-1 - uM1-2 Electric parking brake not operating Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

NG

6.CHECK FOR SHORT TO +B
6.CHECK FOR SHORT TO +B
a.

Disconnect the uM1 No. 1 parking brake wire assembly connector.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

C427099C05
1.781,0.417 2.198,0.667 0.417,0.25 5.125,0.417 5.542,0.667 0.417,0.25 3.26,2.167 2.677,1.375 true 1.896,2.167 2.479,1.375 true 1.885,0.469 2.344,0.667 0.458,0.198 10 false A39 5.229,0.458 5.688,0.656 0.458,0.198 10 false uM1 0.5,0.75 0.958,1.031 0.458,0.281 10 false *b 0.167,0.167 0.583,0.417 0.417,0.25 10 false *a 4.583,0.75 5.125,0.948 0.542,0.198 10 false *c 1.76,2.198 2.26,2.448 0.5,0.25 10 false MRR- 3.135,2.198 3.635,2.448 0.5,0.25 10 false MRR+
*a Front view of wire harness connector *b (to Skid Control ECU (Brake Actuator Assembly))
*c (to No. 1 Parking Brake Wire Assembly) - -


Standard Voltage:
Tester Connection Condition Specified Condition
uM1-1 or A39-13 (MRR+) - Body ground Always Below 1 V
uM1-2 or A39-12 (MRR-) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR