Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _54 Brake _086873 PARKING BRAKE _0420959 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model)  C13B516  Electric Parking Brake Actuator Supply Voltage Circuit Voltage Below Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13B516 Electric Parking Brake Actuator Supply Voltage Circuit Voltage Below Threshold
·

Diagnosis Condition:

Ignition switch ON or electric parking brake switch assembly pulled to lock side with ignition switch off.

·

Malfunction Status:

Voltage at terminal +BS is less than 5.4 V*

·

Detection Time:

Approximately 0.5 seconds


HINT:

*: When the auxiliary battery voltage is 12 V.


·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions: C13B516
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ -
Electric parking brake switch assembly pulled to lock side with ignition switch off - ○
Malfunction Status Voltage at terminal +BS is less than 5.4 V*
HINT:

*: When the auxiliary battery voltage is 12 V.


○ ○
Detection Time Approximately 0.5 seconds Approximately 0.5 seconds
Number of Trips 1 trip 1 trip

HINT:

DTC will be stored when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C419806E06
1.813,1.583 3.042,1.781 1.229,0.198 10 false ABS NO. 2 4.188,1.427 4.625,1.667 0.438,0.24 10 false +BS 3.885,1.313 4.323,1.552 0.438,0.24 10 false 14 4.167,2.167 4.667,2.417 0.5,0.25 10 false A39 4.167,2.333 5.75,2.917 1.583,0.583 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)
a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.
C342413C25
1.458,0.125 1.875,0.375 0.417,0.25 2.969,1.813 2.698,0.99 true 1.552,0.167 2.01,0.365 0.458,0.198 10 false A39 2.896,1.854 3.354,2.052 0.458,0.198 10 false +BS 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-14 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR