Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420993 HYBRID CONTROL SYSTEM(for 2WD) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD)  Transmission Control Switch Circuit  


DESCRIPTION

When the shift lever is in S, different ranges can be chosen using the floor shift sequential gate.

WIRING DIAGRAM

C414881E03
1.875,3.427 2.333,3.625 0.458,0.198 10 false H29 1.875,3.604 4.021,4.208 2.146,0.604 10 false Transmission Control Switch (Shift Lock Control Unit Assembly) 1.99,2.01 2.448,2.208 0.458,0.198 10 false 2 2.24,2.01 2.698,2.208 0.458,0.198 10 false E 2.24,1.333 2.698,1.531 0.458,0.198 10 false IG 2.01,1.344 2.469,1.542 0.458,0.198 10 false 4 0.26,1.427 1.198,2.031 0.938,0.604 10 false from ECU-ACC Fuse 3.51,1.344 3.969,1.542 0.458,0.198 10 false S 3.771,1.344 4.229,1.542 0.458,0.198 10 false 5 3.802,2.688 4.26,2.885 0.458,0.198 10 false 1 3.292,2 3.75,2.198 0.458,0.198 10 false SFTU 3.292,2.677 3.75,2.875 0.458,0.198 10 false SFTD 3.792,2.021 4.25,2.219 0.458,0.198 10 false 3 5.229,2.688 5.688,2.885 0.458,0.198 10 false 11 5.208,2.01 5.667,2.208 0.458,0.198 10 false 24 5.219,1.333 5.677,1.531 0.458,0.198 10 false 25 5.521,1.438 5.979,1.635 0.458,0.198 10 false M 5.51,2.115 5.969,2.313 0.458,0.198 10 false SFTU 5.51,2.781 6.031,3.021 0.521,0.24 10 false SFTD 4.99,3.813 5.448,4.01 0.458,0.198 10 false H67 5,3.979 6.802,4.531 1.802,0.552 10 false Hybrid Vehicle Control ECU

PROCEDURE

1.READ VALUE USING GTS (SPORTS SHIFT POSITION)
a.

Read the Data List using the GTS.

Powertrain > Hybrid Control > Data List
Tester Display
Sports Shift Position
50003 397 233
Result:
Result Proceed to
GTS display changes according to shift lever operation A
GTS display does not change according to shift lever operation B



b.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (SPORTS SHIFT UP SIGNAL, SPORTS SHIFT DOWN SIGNAL)

B

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.READ VALUE USING GTS (SPORTS SHIFT UP SIGNAL, SPORTS SHIFT DOWN SIGNAL)
a.

Read the Data List using the GTS.

Powertrain > Hybrid Control > Data List
Tester Display
Sports Shift UP Signal
Sports Shift DOWN Signal
50003 397 83,82
Result:
Result Proceed to
GTS display changes according to transmission control switch operation A
GTS display does not change according to transmission control switch operation B



b.

Turn the ignition switch off.



A

3.CHECK FOR INTERMITTENT PROBLEMS

B

7.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
3.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the H29 transmission control switch (shift lock control unit assembly) connector.


b.

Turn the ignition switch to ON.


c.
C251979C92
1.521,0.344 1.885,0.542 0.365,0.198 1.188,1.708 1.604,1.292 true 2.24,1.708 1.854,1.292 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.583,0.365 1.969,0.604 0.385,0.24 10 false H29 1.083,1.677 1.396,1.833 0.313,0.156 10 false E 2.292,1.646 2.604,1.802 0.313,0.156 10 false IG
*a Front view of wire harness connector
(to Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H29-4 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H29-4 (IG) - Body ground Ignition switch off Below 1 V



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H29-2 (E) - Body ground Ignition switch off Below 1 Ω



g.

Reconnect the H29 transmission control switch (shift lock control unit assembly) connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

NG

CHECK POWER SOURCE CIRCUIT

5.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

OK

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - TRANSMISSION CONTROL SWITCH)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - TRANSMISSION CONTROL SWITCH)
a.

Disconnect the H67 hybrid vehicle control ECU connector.


b.

Turn the ignition switch to ON.


c.
C408033C24
1.469,0.135 1.823,0.385 0.354,0.25 2.865,0.479 2.26,0.969 true 1.927,1.781 2.188,1.198 true 2.604,1.813 2.333,1.188 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 2.594,1.844 2.75,2.042 0.156,0.198 10 false M 2.906,0.375 3.323,0.563 0.417,0.188 10 false SFTD 1.75,1.833 2.167,2.021 0.417,0.188 10 false SFTU 1.521,0.188 1.875,0.396 0.354,0.208 10 false H67
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard Voltage:
Tester Connection Condition Specified Condition
H67-25 (M) - Body ground Ignition switch ON
Shift lever in S, "+" or "-"
11 to 14 V
Ignition switch ON
Except shift lever in S, "+" and "-"
Below 1 V


NOTICE:

If the ignition switch is turned to ON with the hybrid vehicle control ECU connector disconnected, other DTCs will be stored. After performing the inspection, clear the DTCs.



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-24 (SFTU) - Body ground Shift lever held in "+" Below 1 Ω
H67-24 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
H67-11 (SFTD) - Body ground Shift lever held in "-" Below 1 Ω
H67-11 (SFTD) - Body ground Shift lever in S 10 kΩ or higher



f.

Reconnect the H67 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - HYBRID VEHICLE CONTROL ECU)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H67 hybrid vehicle control ECU connector.


b.
C408033C25
1.438,0.083 1.854,0.354 0.417,0.271 2.719,1.771 2.25,1.021 true 1.927,1.781 2.188,1.198 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 2.615,1.833 3.031,2.021 0.417,0.188 10 false SFTD 1.75,1.833 2.167,2.021 0.417,0.188 10 false SFTU 1.51,0.135 1.813,0.313 0.302,0.177 10 false H67
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-24 (SFTU) - Body ground Shift lever held in "+" Below 1 Ω
H67-24 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
H67-11 (SFTD) - Body ground Shift lever held in "-" Below 1 Ω
H67-11 (SFTD) - Body ground Shift lever in S 10 kΩ or higher



c.

Reconnect the H67 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR