Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  Indicator Circuit  


DESCRIPTION

In accordance with the shift lever position, each shift position indicator light will turn on.

WIRING DIAGRAM

A396736E20
0.083,0.979 1.229,1.208 1.146,0.229 10 false from ACC Relay 1.417,1.177 2.49,1.375 1.073,0.198 10 false ECU-ACC 2.365,0.896 2.635,1.125 0.271,0.229 10 false 5 2.573,1.01 3.031,1.208 0.458,0.198 10 false PWR 3.594,1.021 3.75,1.219 0.156,0.198 10 false P 3.594,1.448 3.75,1.646 0.156,0.198 10 false R 3.594,1.875 3.75,2.094 0.156,0.219 10 false N 3.604,2.302 3.76,2.521 0.156,0.219 10 false D 3.604,2.729 3.76,2.948 0.156,0.219 10 false S 3.813,0.938 3.969,1.135 0.156,0.198 10 false 6 3.813,1.354 3.969,1.552 0.156,0.198 10 false 7 3.813,1.781 3.969,1.979 0.156,0.198 10 false 8 3.813,2.198 3.969,2.396 0.156,0.198 10 false 9 3.813,2.635 4.115,2.906 0.302,0.271 10 false 10 5.656,0.521 6.271,0.719 0.615,0.198 10 false ACCI 5.667,1.031 6.281,1.229 0.615,0.198 10 false INDP 5.667,1.458 6.281,1.656 0.615,0.198 10 false INDR 5.667,1.885 6.281,2.083 0.615,0.198 10 false INDN 5.677,2.313 6.292,2.51 0.615,0.198 10 false INDD 5.677,2.719 6.292,2.917 0.615,0.198 10 false INDM 5.333,0.333 5.646,0.531 0.313,0.198 10 false 29 5.333,0.844 5.646,1.042 0.313,0.198 10 false 19 5.375,1.271 5.688,1.469 0.313,0.198 10 false 7 5.333,1.688 5.646,1.885 0.313,0.198 10 false 21 5.365,2.115 5.677,2.313 0.313,0.198 10 false 8 5.333,2.531 5.646,2.729 0.313,0.198 10 false 20 5.281,0.521 5.74,0.719 0.458,0.198 10 false A32 5.292,1.042 5.906,1.24 0.615,0.198 10 false H67 5.292,1.469 5.906,1.667 0.615,0.198 10 false H67 5.292,1.885 5.906,2.083 0.615,0.198 10 false H67 5.292,2.313 5.906,2.51 0.615,0.198 10 false H67 5.292,2.729 5.906,2.927 0.615,0.198 10 false H67 2.51,3.219 2.823,3.417 0.313,0.198 10 false P1 2.5,3.375 4.229,3.688 1.729,0.313 10 false Shift Position Indicator 5.375,3.167 6.781,3.594 1.406,0.427 10 false Hybrid Vehicle Control ECU

PROCEDURE

1.CHECK SHIFT POSITION INDICATOR
a.

Turn the ignition switch to ON (ACC).


b.

Check that each shift position indicator light turns on correctly.

Result:
Result Proceed to
All shift position indicator lights turn on simultaneously A
Shift position indicator lights other than corresponding one turns on B
Corresponding shift position indicator light does not turn on C
No shift position indicator lights turn on D



c.

Turn the ignition switch off.



A

2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND)

B

2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND)

C

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

D

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND)
a.

Disconnect the H67 hybrid vehicle control ECU connector.


b.
C408033C26
0.073,0.948 0.427,1.198 0.354,0.25 1.177,0.375 1.542,0.958 true 1.167,1.781 1.5,1.188 true 2.052,1.813 1.781,1.188 true 2.115,0.365 1.698,0.958 true 1.604,1.813 1.635,1.177 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.969,0.198 1.385,0.385 0.417,0.188 10 false INDR 0.99,1.833 1.406,2.021 0.417,0.188 10 false INDP 0.135,0.979 0.438,1.156 0.302,0.177 10 false H67 2.063,0.167 2.479,0.354 0.417,0.188 10 false INDD 1.438,1.844 1.854,2.031 0.417,0.188 10 false INDM 1.938,1.844 2.354,2.031 0.417,0.188 10 false INDN
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-19 (INDP) - Body ground and other terminals Always 10 kΩ or higher
H67-7 (INDR) - Body ground and other terminals Always 10 kΩ or higher
H67-21 (INDN) - Body ground and other terminals Always 10 kΩ or higher
H67-8 (INDD) - Body ground and other terminals Always 10 kΩ or higher
H67-20 (INDM) - Body ground and other terminals Always 10 kΩ or higher



c.

Reconnect the H67 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR)
3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR)
a.

Disconnect the H67 hybrid vehicle control ECU connector.


b.

Disconnect the P1 shift position indicator connector.


c.
A443448C01
0.083,1.156 0.479,1.385 0.396,0.229 0.333,3.354 0.729,3.583 0.396,0.229 1.74,3.656 1.729,4.104 true 1.365,4.073 1.573,3.635 true 2.104,4.104 1.865,3.667 true 1.406,3.635 0.948,4.094 true 2.052,3.677 2.458,4.094 true 1.667,1.208 1.25,0.438 true 1.823,1.24 2.135,0.458 true 1.146,1.958 1.573,1.406 true 1.75,1.979 1.74,1.406 true 2.479,1.979 1.896,1.406 true 0.115,0.156 0.427,0.354 0.313,0.198 10 false *a 0.156,2.448 0.469,2.646 0.313,0.198 10 false *b 0.146,1.198 0.458,1.396 0.313,0.198 10 false H67 0.438,3.385 0.75,3.583 0.313,0.198 10 false P1 1.688,4.135 2,4.333 0.313,0.198 10 false N 2.063,4.135 2.375,4.333 0.313,0.198 10 false D 1.281,4.135 1.594,4.333 0.313,0.198 10 false R 0.854,4.135 1.167,4.333 0.313,0.198 10 false P 2.458,4.135 2.771,4.333 0.313,0.198 10 false S 1.573,2.052 1.99,2.271 0.417,0.219 10 false INDM 2.208,0.313 2.625,0.531 0.417,0.219 10 false INDD 2.448,2.052 2.865,2.271 0.417,0.219 10 false INDN 0.833,2.052 1.25,2.271 0.417,0.219 10 false INDP 0.885,0.292 1.302,0.51 0.417,0.219 10 false INDR
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Shift Position Indicator)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-19 (INDP) or P1-6 (P) - Body ground and other terminals Always 10 kΩ or higher
H67-7 (INDR) or P1-7 (R) - Body ground and other terminals Always 10 kΩ or higher
H67-21 (INDN) or P1-8 (N) - Body ground and other terminals Always 10 kΩ or higher
H67-8 (INDD) or P1-9 (D) - Body ground and other terminals Always 10 kΩ or higher
H67-20 (INDM) or P1-10 (S) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the P1 shift position indicator connector.


e.

Reconnect the H67 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the P1 shift position indicator connector.


b.

Turn the ignition switch to ON (ACC).


c.
A303084C11
0.542,0.958 0.948,1.219 0.406,0.26 2.042,1.188 2.479,0.958 true 0.677,1.021 1.135,1.219 0.458,0.198 10 false P1 2.531,0.854 3.01,1.063 0.479,0.208 10 false PWR 0.063,0.094 0.375,0.25 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Shift Position Indicator)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
P1-5 (PWR) - Body ground Ignition switch on (ACC) 11 to 14 V



d.

Turn the ignition switch off.


e.

Reconnect the P1 shift position indicator connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL ACCI)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL ACCI)
a.

Turn the ignition switch to ON (ACC).


b.

Measure the voltage according to the value(s) in the table below.

C407546C87
3.354,0.333 3.698,0.583 0.344,0.25 3.594,1.5 3.427,2.26 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 3.396,0.375 3.854,0.573 0.458,0.198 10 false A32 3.26,2.323 3.656,2.521 0.396,0.198 10 false ACCI
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A32-29 (ACCI) - Body ground Ignition switch ON (ACC) 11 to 14 V



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

6.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)
a.

Disconnect the H67 hybrid vehicle control ECU connector.


b.

Turn the ignition switch to ON (ACC).


c.
C408033C27
0.073,0.948 0.427,1.198 0.354,0.25 1.177,0.375 1.542,0.958 true 1.167,1.781 1.5,1.188 true 2.052,1.813 1.781,1.188 true 2.115,0.365 1.698,0.958 true 1.604,1.813 1.635,1.177 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.969,0.198 1.385,0.385 0.417,0.188 10 false INDR 0.99,1.833 1.406,2.021 0.417,0.188 10 false INDP 0.135,0.979 0.438,1.156 0.302,0.177 10 false H67 2.063,0.167 2.479,0.354 0.417,0.188 10 false INDD 1.438,1.844 1.854,2.031 0.417,0.188 10 false INDM 1.938,1.844 2.354,2.031 0.417,0.188 10 false INDN
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H67-19 (INDP) - Body ground and other terminals Ignition switch ON (ACC) 11 to 14 V
H67-7 (INDR) - Body ground and other terminals Ignition switch ON (ACC) 11 to 14 V
H67-21 (INDN) - Body ground and other terminals Ignition switch ON (ACC) 11 to 14 V
H67-8 (INDD) - Body ground and other terminals Ignition switch ON (ACC) 11 to 14 V
H67-20 (INDM) - Body ground and other terminals Ignition switch ON (ACC) 11 to 14 V



d.

Turn the ignition switch off.


e.

Reconnect the H67 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR)
7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR)
a.

Disconnect the H67 hybrid vehicle control ECU connector.


b.

Disconnect the P1 shift position indicator connector.


c.
A443448C01
0.083,1.156 0.479,1.385 0.396,0.229 0.333,3.354 0.729,3.583 0.396,0.229 1.74,3.656 1.729,4.104 true 1.365,4.073 1.573,3.635 true 2.104,4.104 1.865,3.667 true 1.406,3.635 0.948,4.094 true 2.052,3.677 2.458,4.094 true 1.667,1.208 1.25,0.438 true 1.823,1.24 2.135,0.458 true 1.146,1.958 1.573,1.406 true 1.75,1.979 1.74,1.406 true 2.479,1.979 1.896,1.406 true 0.115,0.156 0.427,0.354 0.313,0.198 10 false *a 0.156,2.448 0.469,2.646 0.313,0.198 10 false *b 0.146,1.198 0.458,1.396 0.313,0.198 10 false H67 0.438,3.385 0.75,3.583 0.313,0.198 10 false P1 1.688,4.135 2,4.333 0.313,0.198 10 false N 2.063,4.135 2.375,4.333 0.313,0.198 10 false D 1.281,4.135 1.594,4.333 0.313,0.198 10 false R 0.854,4.135 1.167,4.333 0.313,0.198 10 false P 2.458,4.135 2.771,4.333 0.313,0.198 10 false S 1.573,2.052 1.99,2.271 0.417,0.219 10 false INDM 2.208,0.313 2.625,0.531 0.417,0.219 10 false INDD 2.448,2.052 2.865,2.271 0.417,0.219 10 false INDN 0.833,2.052 1.25,2.271 0.417,0.219 10 false INDP 0.885,0.292 1.302,0.51 0.417,0.219 10 false INDR
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Shift Position Indicator)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-19 (INDP) - P1-6 (P) Always Below 1 Ω
H67-7 (INDR) - P1-7 (R) Always Below 1 Ω
H67-21 (INDN) - P1-8 (N) Always Below 1 Ω
H67-8 (INDD) - P1-9 (D) Always Below 1 Ω
H67-20 (INDM) - P1-10 (S) Always Below 1 Ω



d.

Reconnect the P1 shift position indicator connector.


e.

Reconnect the H67 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR