Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  P0A1B94  Drive Motor "A" Control Module Unexpected Operation  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU monitors the motor generator control ECU (MG ECU).

The cause of this malfunction may be the following:

Motor generator control ECU internal malfunction
·

Motor generator control ECU (MG ECU) malfunction



DESCRIPTION

The hybrid vehicle control ECU monitors the motor generator control ECU (MG ECU) and stores this DTC when it detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A1B94 Drive Motor "A" Control Module Unexpected Operation The motor generator control ECU (MG ECU) value received by the hybrid vehicle control ECU exceeds the threshold for a certain period of time.
(1 trip detection logic)
·

Inverter with converter assembly

·

IGCT relay

·

IGCT-IG fuse


Comes on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

With ignition switch ON and wait for 2 minutes or more.

HINT:

If the vehicle has returned to normal, it can be driven after turning the ignition switch to ON (READY).


7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A456900E01
0.781,3.115 2.146,3.375 1.365,0.26 10 false Auxiliary Battery 0.521,4.281 0.958,4.479 0.438,0.198 10 false OA 1.885,1.125 2.25,1.406 0.365,0.281 10 false 2 0.677,1.979 1.635,2.208 0.958,0.229 10 false IGCT-IG 1.885,0.698 2.167,0.958 0.281,0.26 10 false 3 2.667,0.698 2.865,0.896 0.198,0.198 10 false 5 2.208,1.563 2.573,1.844 0.365,0.281 10 false IGCT 2.646,1.125 3.01,1.406 0.365,0.281 10 false 1 4.167,3.135 4.531,3.417 0.365,0.281 10 false 1 4.094,3.427 4.917,3.677 0.823,0.25 10 false IGCT NO. 3 4.052,0.958 4.833,1.271 0.781,0.313 10 false IGCT NO. 1 5.167,2.271 7.073,2.542 1.906,0.271 10 false Hybrid Vehicle Control ECU 5.396,4.094 6.802,4.656 1.406,0.563 10 false Inverter with Converter Assembly 5.635,3.24 6,3.521 0.365,0.281 10 false IGCT 5.615,3.573 6.156,3.854 0.542,0.281 10 false GND1 5.667,1.698 6.031,1.979 0.365,0.281 10 false E1 5.667,1.24 6.156,1.573 0.49,0.333 10 false MREL 5.667,0.813 6.031,1.094 0.365,0.281 10 false +B2 5.656,0.385 6.021,0.667 0.365,0.281 10 false +B1 4.656,3.135 5.021,3.417 0.365,0.281 10 false 2 4.115,0.708 4.479,0.99 0.365,0.281 10 false 1 4.594,0.708 4.958,0.99 0.365,0.281 10 false 2 5.396,0.188 5.76,0.406 0.365,0.219 10 false 11 5.323,0.375 5.688,0.594 0.365,0.219 10 false A31 5.385,0.615 5.75,0.833 0.365,0.219 10 false 1 5.313,0.802 5.677,1.021 0.365,0.219 10 false H67 5.385,1.042 5.75,1.26 0.365,0.219 10 false 5 5.323,1.208 5.688,1.427 0.365,0.219 10 false A31 5.385,1.5 5.75,1.719 0.365,0.219 10 false 3 5.313,1.677 5.677,1.896 0.365,0.219 10 false H67 5.365,3.125 5.771,3.344 0.406,0.219 10 false 26 5.458,3.469 5.823,3.688 0.365,0.219 10 false 9 5.385,3.948 5.75,4.167 0.365,0.219 10 false A55

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
a.

Check the connection of the negative (-) and positive (+) auxiliary battery terminals.

OK:

The terminals are connected securely and there is no contact problem.


HINT:

If performing a simulation test, turn the ignition switch to ON and shake the wire harnesses vertically and horizontally before checking for DTCs.



Result:
Proceed to
OK
NG



OK

2.CHECK GROUND WIRE CONNECTION CONDITION

NG

6.CONNECT SECURELY
2.CHECK GROUND WIRE CONNECTION CONDITION
a.

Check the installation condition of the ground wires OA.

OK:

The ground wires OA are securely installed.


HINT:

If performing a simulation test, turn the ignition switch to ON and shake the wire harnesses vertically and horizontally before checking for DTCs.



Result:
Proceed to
OK
NG



OK

3.CHECK FUSE (IGCT-IG)

NG

7.CONNECT SECURELY
3.CHECK FUSE (IGCT-IG)
a.
A443442C01
1.354,0.667 1.958,0.51 true 0.146,0.167 0.458,0.365 0.313,0.198 10 false *1 1.167,0.646 1.479,0.844 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and NO. 5 Floor Junction Block Assembly
*2 IGCT-IG Fuse


Remove the IGCT-IG fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT-IG fuse Always Below 1 Ω



c.

Reinstall the IGCT-IG fuse.


Result:
Proceed to
OK
NG



OK

4.CHECK RELAY (IGCT)

NG

8.REPAIR OR REPLACE MALFUNCTIONING PARTS
4.CHECK RELAY (IGCT)
a.

Check the IGCT relay for improper installation.

OK:

The relay is installed securely.


HINT:

If performing a simulation test, turn the ignition switch to ON and gently vibrate the IGCT relay with a finger before checking for DTCs.



b.
A443441C01
0.76,2.188 1.375,1.865 true 0.146,0.167 0.458,0.365 0.313,0.198 10 false *1 0.531,2.146 0.844,2.344 0.313,0.198 10 false *2
*1 No. 5 Relay Block and No. 5 Floor Junction Block Assembly
*2 IGCT Relay


Remove the IGCT relay from the No. 5 floor relay block and No. 5 floor junction block assembly.


c.
A253297C01
0.146,0.056 0.409,0.261 0.263,0.205 10 *1
*1 IGCT Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



d.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT (HYBRID CONTROL)

NG

9.REPAIR OR REPLACE MALFUNCTIONING PARTS
5.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

HINT:

Check the DTCs that were output when the vehicle was brought to the workshop.


Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0A1B94 only is output. A
DTCs except P0A1B94 are output. B



b.

Turn the ignition switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

6.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
7.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
8.REPAIR OR REPLACE MALFUNCTIONING PARTS
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
9.REPAIR OR REPLACE MALFUNCTIONING PARTS
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC

NEXT

11.SIMULATION TEST
11.SIMULATION TEST
a.

Turn the ignition switch to ON and wait for 2 minutes or more.


b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT (HYBRID CONTROL)
12.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs are output. A
P0A1B94 only is output. B
DTCs except P0A1B94 are output. C



b.

Turn the ignition switch off.



A

END

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

C