Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  P0B231C  Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU detects a VB sensor malfunction.

The cause of this malfunction may be one of the following:

Battery voltage sensor VB sensor internal circuit malfunction
·

Battery voltage sensor malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction

HV battery malfunction



DESCRIPTION

The battery voltage sensor sends HV battery voltage information to the hybrid vehicle control ECU via serial communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range Battery voltage sensor malfunction:
When not boosting, difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is large and difference between "Hybrid Battery Voltage" and "VH-Voltage after Boosting" is large.
(1 trip detection logic)
Battery voltage sensor Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0B231C
·

Hybrid Battery Voltage

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Boost Ratio



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Turn the ignition switch to ON (READY).

7.

With the shift lever in D, depress both the accelerator pedal and brake pedal at the same time to raise the "Hybrid Battery SOC" to a sufficient level.

8.

Move the shift lever to P, check that the engine is stopped and move the shift lever to N.

9.

Set the A/C for maximum cooling.

10.

Leave the vehicle for a few minutes.

HINT:

After the repair if "VL-Voltage before Boosting" and the "Hybrid Battery Voltage" are approximately the same when the ignition switch is turned to ON (READY) with shift lever in P and the accelerator pedal not depressed, the condition is judged as normal.


11.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

12.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

NOTICE:

Performing the check procedures for a long time with shift lever in N may cause DTC P300000 to be set.


HINT:
·

If the battery voltage sensor has been replaced, it is necessary to confirm the voltage of each battery block. With ignition switch ON (READY), shift lever in P, the engine stopped and the HV battery voltage at 224 V or more, check the value of Data List items "Hybrid Battery Voltage", "VL-Voltage before Boosting" and "VH-Voltage after Boosting". When the system is normal, the values of "Hybrid Battery Voltage", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" should be almost equal. If the difference between each value is more than the voltages specified below, the system is malfunctioning.

Inspection Voltage Maximum Voltage Difference
Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" 40 V
Difference between "Hybrid Battery Voltage" and "VH-Voltage after Boosting" 47 V
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" 62 V



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR)
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P0B231C only is output, or DTCs except the ones in the table below are also output. A
DTCs of Hybrid Control System in the tables below are output. B
DTCs of Motor Generator Control System in the tables below are output. C


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid Control System P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P0AFC00 Hybrid/EV Battery Sensor Module
P0AFC96 Hybrid/EV Battery Sensor Module Component Internal Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
Motor Generator Control System P0A1B1F Generator Control Module Circuit Intermittent
P0A1A47 Generator Control Module Watchdog / Safety MC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Power source circuit malfunction Hybrid Control System P0AFC16 Hybrid/EV Battery Sensor Module Circuit Voltage Below Threshold
Motor Generator Control System P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
Communication system malfunction Hybrid Control System P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U029A87 Lost Communication with Hybrid/EV Battery Sensor Module Missing Message
Sensor and actuator circuit malfunction Hybrid Control System P0B3B14 Hybrid/EV Battery Voltage Sensor "A" Circuit Short to Ground or Open
P0B4014 Hybrid/EV Battery Voltage Sensor "B" Circuit Short to Ground or Open
P0B4514 Hybrid/EV Battery Voltage Sensor "C" Circuit Short to Ground or Open
P0B4A14 Hybrid/EV Battery Voltage Sensor "D" Circuit Short to Ground or Open
P0B4F14 Hybrid/EV Battery Voltage Sensor "E" Circuit Short to Ground or Open
P0B5414 Hybrid/EV Battery Voltage Sensor "F" Circuit Short to Ground or Open
P0B5914 Hybrid/EV Battery Voltage Sensor "G" Circuit Short to Ground or Open
P0B5E14 Hybrid/EV Battery Voltage Sensor "H" Circuit Short to Ground or Open
P0B6314 Hybrid/EV Battery Voltage Sensor "I" Circuit Short to Ground or Open
P0B6814 Hybrid/EV Battery Voltage Sensor "J" Circuit Short to Ground or Open
P0B6D14 Hybrid/EV Battery Voltage Sensor "K" Circuit Short to Ground or Open
P0B7214 Hybrid/EV Battery Voltage Sensor "L" Circuit Short to Ground or Open
P0B7714 Hybrid/EV Battery Voltage Sensor "M" Circuit Short to Ground or Open
P308A13 Hybrid/EV Battery Voltage Sensor All Circuit Open
P0AFC62 Hybrid/EV Battery Sensor Module Signal Compare Failure
P308A12 Hybrid/EV Battery Voltage Sensor All Circuit Short to Auxiliary Battery
System malfunction Motor Generator Control System P0D2D16 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Above Threshold
P0E3116 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold
P0E3117 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold

HINT:
·

P0B231C may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





b.

Turn the ignition switch off.



A

B

C