Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420995 MOTOR GENERATOR CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for 2WD)  P1BFCA2  Battery Discharge Control Circuit System Voltage Low  


DESCRIPTION

The motor generator ECU located in the inverter with converter assembly receives power from the IGCT power source line and discharge control power source line. A semiconductor switch is installed in the motor generator ECU to switch which is used to switch the discharge control power source line power source on and off.

The motor generator ECU outputs the following DTC when it detects a discharge control power source line wiring malfunction or a semiconductor switch stuck off malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1BFCA2 Battery Discharge Control Circuit System Voltage Low When the motor generator ECU is started, the discharge control BAT switch command flag is changed from OFF to ON after a certain period of time elapses, but the discharge control BAT voltage does not increase.
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Fuse


Does not come on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

With the ignition switch ON and wait for 10 seconds or more.

7.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

C414515E05
1.198,2.333 1.521,2.51 0.323,0.177 10 false MG 1.052,0.51 1.667,0.792 0.615,0.281 10 false IGCT-IG 2.156,0.958 2.531,1.177 0.375,0.219 10 false IGCT 3.458,0.5 3.792,0.698 0.333,0.198 10 false PCU 4.698,0.333 4.958,0.542 0.26,0.208 10 false +B 4.698,0.625 5.083,0.865 0.385,0.24 10 false +B2 4.396,0.229 4.625,0.438 0.229,0.208 10 false 36 4.406,0.5 4.635,0.708 0.229,0.208 10 false 35 3.24,0.906 3.729,1.083 0.49,0.177 10 false MREL 4.656,2.042 5.042,2.281 0.385,0.24 10 false +B3 4.656,3.01 5.104,3.26 0.448,0.25 10 false GND1 4.646,3.354 5.094,3.604 0.448,0.25 10 false GND2 4.406,2.042 4.625,2.26 0.219,0.219 10 false 27 4.469,2.917 4.698,3.125 0.229,0.208 10 false 9 4.458,3.24 4.688,3.448 0.229,0.208 10 false 8 4.583,4.302 4.927,4.51 0.344,0.208 10 false A55 4.583,4.469 6.615,4.667 2.031,0.198 10 false Inverter with Converter Assembly 2.802,1.323 4.656,1.729 1.854,0.406 10 false Hybrid Vehicle Control ECU 2.802,1.135 3.135,1.333 0.333,0.198 10 false A31 3.052,0.802 3.208,1 0.156,0.198 10 false 5 0.813,3.458 1.958,3.667 1.146,0.208 10 false Auxiliary Battery 6.156,2.521 6.615,2.719 0.458,0.198 10 false ADC 5.615,3.313 6.969,3.521 1.354,0.208 10 false Switch Drive Circuit 4.865,3.823 6.958,4.01 2.094,0.188 10 false Battery Discharge Control Circuit 0.969,2.063 1.125,2.26 0.156,0.198 10 false 1 1.563,2.073 1.719,2.271 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK HARNESS AND CONNECTOR (DISCHARGE CONTROL POWER SOURCE CIRCUIT)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (DISCHARGE CONTROL POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A55 inverter with converter assembly connector.


c.
C412486C08
0.292,0.885 0.667,1.146 0.375,0.26 1.99,0.885 2.604,0.302 true 1.875,0.896 1.906,0.292 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.365,0.948 0.823,1.146 0.458,0.198 10 false A55 2.635,0.135 3.094,0.333 0.458,0.198 10 false GND1 1.74,0.104 2.354,0.302 0.615,0.198 10 false GND2
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-9 (GND1) - Body ground Ignition switch off Below 1 Ω
A55-8 (GND2) - Body ground Ignition switch off Below 1 Ω



d.

Reconnect the A55 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK FUSE (MG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - BODY GROUND)

3.CHECK FUSE (MG)
a.
A456052C01
2.354,0.542 2.76,0.542 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *1 2.813,0.458 3.125,0.656 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 MG Fuse


Remove the MG fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


b.

Check if there is an open circuit in the MG fuse in the No. 5 floor relay block and No. 5 floor junction block assembly.

OK:

There is no open circuit in the MG fuse.



c.

Install the MG fuse.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MG FUSE - INVERTER WITH CONVERTER ASSEMBLY)

NG

REPLACE FUSE (MG)

4.CHECK HARNESS AND CONNECTOR (MG FUSE - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the MG fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


c.

Disconnect the A55 inverter with converter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

A456053C01
1.427,0.594 1.802,0.823 0.375,0.229 2.865,2.594 2.135,1.927 true 3.875,0.365 4.188,0.563 0.313,0.198 10 false *1 0.573,0.344 0.885,0.542 0.313,0.198 10 false *a 5.635,0.625 5.948,0.823 0.313,0.198 10 false *2 1.479,0.625 1.938,0.823 0.458,0.198 10 false A55 2.906,2.625 3.365,2.823 0.458,0.198 10 false +B3
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly *2 MG Fuse Terminal
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2 (MG fuse terminal) - A55-27 (+B3) Ignition switch off Below 1 Ω



e.

Reconnect the A55 inverter with converter assembly connector.


f.

Install the MG fuse.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (MG FUSE - AUXILIARY BATTERY TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MG FUSE - AUXILIARY BATTERY TERMINAL)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the cable from the positive (+) auxiliary battery terminal.


c.
A456054C01
0.167,0.115 0.479,0.313 0.313,0.198 10 false *1 2.427,0.094 2.74,0.292 0.313,0.198 10 false *2
*1 No. 5 Floor Relay Block and No. 5 Floor Junction Block Assembly
*2 MG Fuse Terminal


Remove the MG fuse from the No. 5 floor relay block and No. 5 floor junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (MG fuse terminal) - Auxiliary battery positive (+) cable Ignition switch off Below 1 Ω
1 (MG fuse terminal) - Body ground Ignition switch off 10 kΩ or higher



e.

Connect the cable to the positive (+) auxiliary battery terminal.


f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Install the MG fuse.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (DISCHARGE CONTROL POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (DISCHARGE CONTROL POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A55 inverter with converter assembly connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.
C412486C09
0.292,0.885 0.667,1.146 0.375,0.26 1.99,1.177 2.615,1.802 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.365,0.948 0.823,1.146 0.458,0.198 10 false A55 2.656,1.802 3.115,2 0.458,0.198 10 false +B3
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-27 (+B3) - Body ground Ignition switch off 11 to 14 V



e.

Disconnect the cable from the negative (-) auxiliary battery terminal.


f.

Reconnect the A55 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG