Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM (for 2WD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420995 MOTOR GENERATOR CONTROL SYSTEM(for 2WD) C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for 2WD)  P322F15  Communication Error from Airbag to Generator Circuit Short to Battery or Open  


DESCRIPTION

Refer to the description for DTC P322F11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>P322F11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P322F15 Communication Error from Airbag to Generator Circuit Short to Battery or Open Open or short to +B in the communication circuit:
Communication from the airbag sensor assembly stopped and circuit high has been detected for a certain period.
·

Inverter with converter assembly

·

Airbag sensor assembly

·

Wire harness or connector


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P322F15 Airbag Status (Collision) (CAN) (Hybrid control system)

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

With ignition switch ON and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>P322F11

Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 2WD)>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)

OK

4.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

NG

CONNECT SECURELY

4.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BODY GROUND)
a.

Disconnect the H58 airbag sensor assembly connector.


b.
C384271C10
0.479,0.938 0.792,1.167 0.313,0.229 2.521,1.802 1.854,1.458 true 0.104,0.083 0.344,0.26 0.24,0.177 10 false *a 2.552,1.823 3.063,2 0.51,0.177 10 false E1 0.521,0.979 0.833,1.156 0.313,0.177 10 false H58
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H58-33 (E1) - Body ground Ignition switch off Below 1 Ω



c.

Reconnect the H58 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A55 inverter with converter assembly connector.


c.

Disconnect the H58 airbag sensor assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


f.
C414518C03
0.396,1.063 0.771,1.281 0.375,0.219 0.49,3.104 0.896,3.344 0.406,0.24 2.656,0.5 2.031,1.188 true 1.875,3.521 2.406,4.177 true 0.458,1.094 0.76,1.313 0.302,0.219 10 false A55 2.708,0.323 3.208,0.552 0.5,0.229 10 false ABFS 0.146,0.135 0.646,0.365 0.5,0.229 10 false *a 0.552,3.146 1.052,3.375 0.5,0.229 10 false H58 2.417,4.229 2.917,4.458 0.5,0.229 10 false GSW2 0.208,2.26 0.708,2.49 0.5,0.229 10 false *b
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-18 (ABFS) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the airbag sensor assembly connector and the inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the ignition switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Open):
Tester Connection Condition Specified Condition
A55-18 (ABFS) - H58-24 (GSW2) Ignition switch off Below 1 Ω


Standard Resistance (Short):
Tester Connection Condition Specified Condition
A55-18 (ABFS) or H58-24 (GSW2) - Body ground and other terminals Ignition switch off 10 kΩ or higher



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Reconnect the H58 airbag sensor assembly connector.


k.

Reconnect the A55 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE AIR BAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE AIR BAG SENSOR ASSEMBLY

NEXT

7.CLEAR DTC
7.CLEAR DTC

NEXT

8.CHECK DTC OUTPUT (MOTOR GENERATOR)
8.CHECK DTC OUTPUT (MOTOR GENERATOR)
a.

Check for DTCs.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P322F15 is not output. A
P322F15 is output. B



b.

Turn the ignition switch off.



A

COMPLETED

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY