Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420996 MOTOR GENERATOR CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for 4WD/AWD)  P1CAC49  Generator Position Sensor Internal Electronic Failure  P1C641F  Generator Control Module Circuit Intermittent  P1CAF38  Generator Position Sensor REF Signal Cycle Malfunction Signal Frequency Incorrect  


DESCRIPTION

The motor generator control ECU (MG ECU), which is built into the inverter with converter assembly, monitors its internal operation and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C641F Generator Control Module Circuit Intermittent Excitation signal (REF signal) for resolver angle detection cycle malfunction detected when DTC P0C7917, P0D3319, P1C5D19, P1C5F19 or P1C5E19 is stored.
(1 trip detection logic)
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Rear traction motor with transaxle assembly

·

Wire harness or connector


Does not come on Master Warning:
Does not come on
P1CAC49 Generator Position Sensor Internal Electronic Failure Generator resolver angle malfunction:
The difference between the resolver angle for control and estimated resolver angle exceeds the allowable limit.
(1 trip detection logic)
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Rear traction motor with transaxle assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P1CAF38 Generator Position Sensor REF Signal Cycle Malfunction Signal Frequency Incorrect Resolver REF signal cycle malfunction:
Excitation signal (REF signal) for resolver angle detection cycle malfunction
(1 trip detection logic)
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Rear traction motor with transaxle assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P1C641F Generator Revolution
P1CAC49
P1CAF38

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

With ignition switch ON and wait for 5 seconds or more.*

*: Lightly wiggle the connectors and wire harnesses up and down and right and left.

7.

Turn the ignition switch to ON (READY) and wait for 5 seconds or more.

8.

Depress the accelerator pedal of the vehicle with the engine stopped and shift lever in P to start the engine.

9.

Keep the engine running for 5 seconds or more.

10.

Drive the vehicle forward with the shift lever in D for 5 m (16 ft.) or more.

11.

Drive the vehicle backward with the shift lever in R for 5 m (16 ft.) or more.

12.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

13.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

C414634E02
0.75,0.188 1.781,0.385 1.031,0.198 10 false Excitation Coil 0.75,2.813 1.781,3.01 1.031,0.198 10 false Excitation Coil 0.75,5.875 1.781,6.073 1.031,0.198 10 false Excitation Coil 5.646,0.51 6.813,0.688 1.167,0.177 10 false Oscillation Circuit 5,0.406 6.167,0.583 1.167,0.177 10 false GRF 5,0.729 6.167,0.906 1.167,0.177 10 false GRFG 5,1.177 6.167,1.354 1.167,0.177 10 false GSN 5,1.5 6.167,1.677 1.167,0.177 10 false GSNG 5,1.833 6.167,2.01 1.167,0.177 10 false GCS 5,2.156 6.167,2.333 1.167,0.177 10 false GCSG 5,2.5 6.167,2.677 1.167,0.177 10 false DRN3 5,3.042 6.167,3.219 1.167,0.177 10 false MRF 5,3.365 6.167,3.542 1.167,0.177 10 false MRFG 5,3.802 6.167,3.979 1.167,0.177 10 false MSN 5,4.135 6.167,4.313 1.167,0.177 10 false MSNG 5,4.458 6.167,4.635 1.167,0.177 10 false MCS 5,4.781 6.167,4.958 1.167,0.177 10 false MCSG 5,5.469 6.167,5.646 1.167,0.177 10 false DRN7 5,6.104 6.167,6.281 1.167,0.177 10 false RRF 5,6.427 6.167,6.604 1.167,0.177 10 false RRFG 5,6.885 6.167,7.063 1.167,0.177 10 false RSN 5,7.198 6.167,7.375 1.167,0.177 10 false RSNG 5,7.542 6.167,7.719 1.167,0.177 10 false RCS 5,7.865 6.167,8.042 1.167,0.177 10 false RCSG 2.542,0.406 3.708,0.583 1.167,0.177 10 false GRF 2.427,0.729 3.594,0.906 1.167,0.177 10 false GRFG 2.521,1.052 3.688,1.229 1.167,0.177 10 false GSN 2.427,1.385 3.594,1.563 1.167,0.177 10 false GSNG 2.531,1.719 3.698,1.896 1.167,0.177 10 false GCS 2.417,2.042 3.583,2.219 1.167,0.177 10 false GCSG 2.5,3.031 3.667,3.208 1.167,0.177 10 false MRF 2.396,3.365 3.563,3.542 1.167,0.177 10 false MRFG 2.49,3.698 3.656,3.875 1.167,0.177 10 false MSN 2.396,4.01 3.563,4.188 1.167,0.177 10 false MSNG 2.51,4.344 3.677,4.521 1.167,0.177 10 false MCS 2.417,4.677 3.583,4.854 1.167,0.177 10 false MCSG 2.979,0.406 4.146,0.583 1.167,0.177 10 false 1 2.99,0.719 4.156,0.896 1.167,0.177 10 false 8 2.969,1.052 4.135,1.229 1.167,0.177 10 false 12 3,1.396 4.167,1.573 1.167,0.177 10 false 2 2.99,1.719 4.156,1.896 1.167,0.177 10 false 7 2.969,2.042 4.135,2.219 1.167,0.177 10 false 11 4.719,0.365 5.885,0.542 1.167,0.177 10 false 8 4.729,0.698 5.896,0.875 1.167,0.177 10 false 9 4.688,1.021 5.854,1.198 1.167,0.177 10 false 10 4.688,1.344 5.854,1.521 1.167,0.177 10 false 11 4.698,1.667 5.865,1.844 1.167,0.177 10 false 13 4.677,2 5.844,2.177 1.167,0.177 10 false 12 4.74,2.354 5.906,2.531 1.167,0.177 10 false 7 2.969,3.031 4.135,3.208 1.167,0.177 10 false 6 2.979,3.365 4.146,3.542 1.167,0.177 10 false 9 2.99,3.688 4.156,3.865 1.167,0.177 10 false 4 2.99,4.021 4.156,4.198 1.167,0.177 10 false 5 2.979,4.344 4.146,4.521 1.167,0.177 10 false 10 2.99,4.677 4.156,4.854 1.167,0.177 10 false 14 4.729,3 5.896,3.177 1.167,0.177 10 false 5 4.729,3.323 5.896,3.5 1.167,0.177 10 false 6 4.719,3.656 5.885,3.833 1.167,0.177 10 false 1 4.729,3.979 5.896,4.156 1.167,0.177 10 false 2 4.74,4.313 5.906,4.49 1.167,0.177 10 false 4 4.74,4.635 5.906,4.813 1.167,0.177 10 false 3 0.677,5.385 1.844,5.563 1.167,0.177 10 false C63 0.677,2.396 3.427,2.594 2.75,0.198 10 false Generator Resolver 0.667,5.031 3.417,5.229 2.75,0.198 10 false Motor Resolver 0.448,8.469 1.615,8.646 1.167,0.177 10 false N4 0.688,8.479 3.792,8.708 3.104,0.229 10 false Rear Traction Motor with Transaxle Assembly 0.667,8.104 3.417,8.302 2.75,0.198 10 false Rear Motor Resolver 0.99,5.396 3.75,5.604 2.76,0.208 10 false Hybrid Vehicle Transaxle Assembly 4.896,8.458 6.969,8.688 2.073,0.229 10 false Inverter with Converter Assembly 2.521,6.115 3.688,6.292 1.167,0.177 10 false RRF 2.438,6.438 3.604,6.615 1.167,0.177 10 false RRFG 2.542,6.771 3.708,6.948 1.167,0.177 10 false RSN 2.448,7.094 3.615,7.271 1.167,0.177 10 false RSNG 2.552,7.417 3.719,7.594 1.167,0.177 10 false RCS 2.458,7.74 3.625,7.917 1.167,0.177 10 false RCSG 4.698,6.073 5.865,6.25 1.167,0.177 10 false 28 4.729,6.396 5.896,6.573 1.167,0.177 10 false 1 4.698,6.729 5.865,6.906 1.167,0.177 10 false 19 4.698,7.052 5.865,7.229 1.167,0.177 10 false 10 4.708,7.385 5.875,7.563 1.167,0.177 10 false 29 4.698,7.708 5.865,7.885 1.167,0.177 10 false 20 4.688,5.313 5.854,5.49 1.167,0.177 10 false 11 2.979,6.115 4.146,6.292 1.167,0.177 10 false 4 2.979,6.438 4.146,6.615 1.167,0.177 10 false 6 2.99,6.771 4.156,6.948 1.167,0.177 10 false 3 2.99,7.104 4.156,7.281 1.167,0.177 10 false 7 2.99,7.417 4.156,7.594 1.167,0.177 10 false 2 2.99,7.75 4.156,7.927 1.167,0.177 10 false 8 4.646,5.469 5.104,5.667 0.458,0.198 10 false A55 4.646,6.229 5.104,6.427 0.458,0.198 10 false A55 4.646,6.552 5.104,6.75 0.458,0.198 10 false A55 4.646,6.885 5.104,7.083 0.458,0.198 10 false A55 4.646,7.208 5.104,7.406 0.458,0.198 10 false A55 4.646,7.531 5.104,7.729 0.458,0.198 10 false A55 4.635,7.854 5.094,8.052 0.458,0.198 10 false A55 4.635,0.521 5.094,0.719 0.458,0.198 10 false C61 4.635,0.854 5.094,1.052 0.458,0.198 10 false C61 4.646,1.177 5.104,1.375 0.458,0.198 10 false C61 4.646,1.51 5.104,1.708 0.458,0.198 10 false C61 4.646,1.833 5.104,2.031 0.458,0.198 10 false C61 4.656,2.156 5.115,2.354 0.458,0.198 10 false C61 4.635,2.51 5.094,2.708 0.458,0.198 10 false C61 4.646,3.146 5.104,3.344 0.458,0.198 10 false C61 4.635,3.479 5.094,3.677 0.458,0.198 10 false C61 4.635,3.813 5.094,4.01 0.458,0.198 10 false C61 4.646,4.135 5.104,4.333 0.458,0.198 10 false C61 4.635,4.469 5.094,4.667 0.458,0.198 10 false C61 4.646,4.792 5.104,4.99 0.458,0.198 10 false C61

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


HINT:
·

If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.

·

If the resolver is malfunctioning, the vehicle may not drive smoothly.

·

When inspecting the connectors, if it is difficult to judge if a connector was disconnected, deformed or improperly secured, disconnect and reconnect the connector and then check for DTCs again. Check if the same DTC is output. If the same DTC is not output, improper connection of connectors is suspected.

·

As a malfunction detection threshold may be exceeded when performing the vibration or heat connector inspections, make sure to perform the following inspection to check that the DTC was not stored due to the malfunction of a part.



PROCEDURE

1.CHECK DTC OUTPUT (MOTOR GENERATOR)
a.

Check for DTCs.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P1CAC49, P1CAF38 or P1C641F only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


System Relevant DTC
Motor generator control system P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A4516 Drive Motor B" Position Sensor Circuit Voltage Below Threshold
P0A4B16 Generator Position Sensor Circuit Voltage Below Threshold
P0C6413 Generator Position Sensor Circuit "A" Circuit Open
P0C6416 Generator Position Sensor Circuit "A" Circuit Voltage Below Threshold
P0C6417 Generator Position Sensor Circuit "A" Circuit Voltage Above Threshold
P0C6913 Generator Position Sensor Circuit "B" Circuit Open
P0C6916 Generator Position Sensor Circuit "B" Circuit Voltage Below Threshold
P0C6917 Generator Position Sensor Circuit "B" Circuit Voltage Above Threshold


b.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK GENERATOR RESOLVER CIRCUIT

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK GENERATOR RESOLVER CIRCUIT

NEXT

4.CHECK MOTOR RESOLVER CIRCUIT
4.CHECK MOTOR RESOLVER CIRCUIT

NEXT

5.CHECK REAR MOTOR RESOLVER CIRCUIT
5.CHECK REAR MOTOR RESOLVER CIRCUIT

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Rear Motor Resolver Circuit

HINT:

If the "Rear Motor Resolver Circuit" inspection results are normal, perform the next step.


Result:
Proceed to
NEXT



NEXT

REPLACE INVERTER WITH CONVERTER ASSEMBLY