Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420996 MOTOR GENERATOR CONTROL SYSTEM(for 4WD/AWD) C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for 4WD/AWD)  P322F11  Communication Error from Airbag to Generator Circuit Short to Ground  


DESCRIPTION

The motor generator control ECU located in the inverter with converter assembly detects a problem in the collision signal line from the airbag sensor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P322F11 Communication Error from Airbag to Generator Circuit Short to Ground Short to ground in the communication circuit:
Communication from the airbag sensor assembly stopped and circuit Low has been detected for a certain period.
(1 trip detection logic)
·

Wire harness or connector

·

Airbag sensor assembly

·

Inverter with converter assembly


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P322F11 Airbag Status (Collision) (CAN) (Hybrid control system)

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

With ignition switch ON and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A411939E05
1.896,0.958 2.427,1.167 0.531,0.208 10 false GSW2 2.427,0.958 2.656,1.167 0.229,0.208 10 false 24 2.427,1.271 2.656,1.479 0.229,0.208 10 false 33 2.125,1.281 2.354,1.49 0.229,0.208 10 false E1 1.083,2.26 2.844,2.552 1.76,0.292 10 false Airbag Sensor Assembly 1.083,2.094 1.563,2.292 0.479,0.198 10 false H58 4.646,0.938 4.875,1.146 0.229,0.208 10 false 18 4.906,0.958 5.396,1.156 0.49,0.198 10 false ABFS 5.604,0.448 5.896,0.667 0.292,0.219 10 false +B 4.719,2.094 5.208,2.292 0.49,0.198 10 false A55 4.719,2.281 6.875,2.552 2.156,0.271 10 false Inverter with Converter Assembly

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B



b.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for 4WD/AWD)>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)
a.
C374925C18
0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Component with harness connected
(Airbag Sensor Assembly)


Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connectors are connected securely and there are no contact pressure problems.


Result:
Proceed to
OK
NG




OK

4.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

CONNECT SECURELY

4.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Disconnect the H58 airbag sensor assembly connector.


b.

Turn the ignition switch to ON.


c.
C384271C09
0.479,0.938 0.792,1.167 0.313,0.229 2.521,1.802 1.854,1.271 true 0.104,0.083 0.344,0.26 0.24,0.177 10 false *a 2.552,1.823 3.063,2 0.51,0.177 10 false GSW2 0.521,0.979 0.833,1.156 0.313,0.177 10 false H58
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H58-24 (GSW2) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the ignition switch off.


e.

Reconnect the H58 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE AIR BAG SENSOR ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
5.REPLACE AIR BAG SENSOR ASSEMBLY

NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Motor Generator > Clear DTCs
50002 395

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT (MOTOR GENERATOR)
7.CHECK DTC OUTPUT (MOTOR GENERATOR)
a.

Check for DTCs.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P322F11 is not output. A
P322F11 is output. B



b.

Turn the ignition switch off.



A

COMPLETED

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A55 inverter with converter assembly connector.


c.

Disconnect the H58 airbag sensor assembly connector.


d.
C414518C02
0.396,1.063 0.771,1.281 0.375,0.219 0.49,3.104 0.896,3.344 0.406,0.24 2.656,0.5 2.031,1.188 true 1.875,3.521 2.406,4.177 true 0.458,1.094 0.76,1.313 0.302,0.219 10 false A55 2.708,0.323 3.208,0.552 0.5,0.229 10 false ABFS 0.146,0.135 0.646,0.365 0.5,0.229 10 false *a 0.552,3.146 1.052,3.375 0.5,0.229 10 false H58 2.417,4.229 2.917,4.458 0.5,0.229 10 false GSW2 0.208,2.26 0.708,2.49 0.5,0.229 10 false *b
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Open):
Tester Connection Condition Specified Condition
A55-18 (ABFS) - H58-24 (GSW2) Ignition switch off Below 1 Ω


Standard Resistance (Short):
Tester Connection Condition Specified Condition
A55-18 (ABFS) or H58-24 (GSW2) - Body ground and other terminals Ignition switch off 10 kΩ or higher



e.

Reconnect the H58 airbag sensor assembly connector.


f.

Reconnect the A55 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR