Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C110E14  Brake Booster Motor "A" Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the No. 1 skid control ECU (brake booster with master cylinder assembly) power source voltage drops, or there is insufficient voltage to operate the main relay, the No. 1 skid control ECU (brake booster with master cylinder assembly) will store these DTCs.

If the auxiliary battery voltage is temporarily low, these DTCs may be stored.

HINT:

DTC C125600 may also be memorized if there is a drop in power source voltage.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
C110E14 Brake Booster Motor "A" Supply Voltage Circuit Short to Ground or Open When the voltage at terminal +BI1 is more than 7.3 V, the voltage at terminal MRI1 is less than 5.7 V for 1 second or more.
·

Improperly connected connector, deformation or corrosion of terminals

·

Wire harness and connector

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

WIRING DIAGRAM

C427346E01
0.375,1.844 1.625,2.208 1.25,0.365 10 false ABS-MAIN 0.375,2.958 1.135,3.198 0.76,0.24 10 false ABS NO. 3 0.26,0.729 1.365,1.01 1.104,0.281 10 false ABS MTR NO. 1 0.24,4.104 1.323,4.365 1.083,0.26 10 false ECU-IG1 NO. 2 0.281,5.25 1.323,5.5 1.042,0.25 10 false ECU-IG2 NO. 3 4.26,1.531 4.573,1.729 0.313,0.198 10 false 15 4.271,2.656 4.583,2.854 0.313,0.198 10 false 14 4.344,0.427 4.656,0.625 0.313,0.198 10 false 1 4.281,3.781 4.594,3.979 0.313,0.198 10 false 31 4.281,4.896 4.594,5.094 0.313,0.198 10 false 42 4.573,1.792 4.885,1.99 0.313,0.198 10 false BS 4.552,2.906 5,3.188 0.448,0.281 10 false +BI1 4.563,0.677 4.99,0.938 0.427,0.26 10 false MRI1 4.563,4.021 4.875,4.219 0.313,0.198 10 false IG1 4.563,5.146 4.875,5.344 0.313,0.198 10 false IG2 4.406,5.688 4.719,5.885 0.313,0.198 10 false A44 4.406,5.865 6.823,6.292 2.417,0.427 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.906,4.896 1.063,5.094 0.156,0.198 10 false 2 0.917,0.417 1.073,0.615 0.156,0.198 10 false 2 0.917,1.531 1.073,1.729 0.156,0.198 10 false 2 0.906,2.646 1.063,2.844 0.156,0.198 10 false 2 0.906,3.771 1.063,3.969 0.156,0.198 10 false 2 5.885,2.781 6.198,2.979 0.313,0.198 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the auxiliary battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only DTC C110E14 is output. A
DTCs other than C110E14 are output. B



A

2.CHECK HARNESS AND CONNECTOR (+BI1 AND MRI1 TERMINAL)

B

2.CHECK HARNESS AND CONNECTOR (+BI1 AND MRI1 TERMINAL)
a.
C423268C11
0.438,0.698 0.844,0.979 0.406,0.281 0.667,2.771 0.813,1.844 true 2.74,2.76 2.49,1.74 true 0.51,0.75 0.969,0.948 0.458,0.198 10 false A44 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 0.51,2.792 0.969,2.99 0.458,0.198 10 false MRI1 2.583,2.792 3.042,2.99 0.458,0.198 10 false +BI1
*a Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-14 (+BI1) - Body ground Always 11 to 14 V
A44-1 (MRI1) - Body ground Always 11 to 14 V



Result:
Result Proceed to
11 to 14 V. A
Below 11 V. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPAIR OR REPLACE HARNESS OR CONNECTOR