Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C050C23  Left Rear Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C050C12.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>C050C12

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C050C23 Left Rear Wheel Speed Sensor Signal Stuck Low Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.*2

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.*1

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 15 seconds or more.*2

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 30 seconds or more.*1


·

Rear skid control sensor LH*1

·

Rear speed sensor LH (rear axle hub and bearing assembly LH)*2

·

Speed sensor installation

·

Skid control sensor wire LH (No. 2 parking brake wire assembly)

·

Wire harness and connector

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

*1: for 4WD/AWD

*2: for 2WD


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for 4WD/AWD. A
for 2WD. B



A

2.CHECK REAR SKID CONTROL SENSOR LH INSTALLATION

B

8.CHECK REAR SPEED SENSOR LH INSTALLATION
2.CHECK REAR SKID CONTROL SENSOR LH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Skid Control Sensor LH
*a Correct
*b Incorrect
*c 8.5 N*m (87 kgf*cm, 75 in.*lbf)
*d No clearance


Check the rear skid control sensor LH installation.

OK:

There is no clearance between the rear skid control sensor LH and the rear axle carrier LH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

3.CHECK REAR SKID CONTROL SENSOR LH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE REAR SKID CONTROL SENSOR LH

3.CHECK REAR SKID CONTROL SENSOR LH (CHECK FOR FOREIGN MATTER)

b.

Check the rear skid control sensor tip LH.

OK:

The rear skid control sensor tip LH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear skid control sensor LH, clean the rear skid control sensor LH.

·

If the rear skid control sensor LH is damaged, replace the rear skid control sensor LH with a new one.




Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (RL WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SKID CONTROL SENSOR LH

4.READ VALUE USING GTS (RL WHEEL SPEED)
a.

Perform a road test.


b.

Check the rear skid control sensor LH output value.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RL Wheel Speed
50003 435 16
OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
5.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
a.
C425604C09
0.813,0.74 1.219,1.021 0.406,0.281 2.354,0.729 2.76,1.01 0.406,0.281 2.948,2.573 2.667,2 true 0.667,2.573 0.917,1.802 true 1.427,2.552 1.156,1.781 true 2.146,2.563 2.427,2 true 0.948,0.792 1.271,1.052 0.323,0.26 10 false u4 2.427,0.792 2.75,1.052 0.323,0.26 10 false uM2 1.271,0.771 1.594,1.031 0.323,0.26 10 false *b 2.833,0.729 3.156,0.99 0.323,0.26 10 false *c 0.135,0.135 0.458,0.396 0.323,0.26 10 false *a 1.396,2.594 1.719,2.854 0.323,0.26 10 false + 2.052,2.615 2.375,2.875 0.323,0.26 10 false RL+ 0.615,2.573 0.938,2.833 0.323,0.26 10 false - 2.865,2.615 3.188,2.875 0.323,0.26 10 false RL-
*a Front view of skid control sensor wire LH (No. 2 parking brake wire assembly)
*b to Sensor Side Connector
*c to Vehicle Side Connector


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the u4 and uM2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
u4-2 (+) - uM2-3 (RL+) Always Below 1 Ω
u4-2 (+) or uM2-3 (RL+) - Body ground and other terminals Always 10 kΩ or higher
u4-1 (-) - uM2-4 (RL-) Always Below 1 Ω
u4-1 (-) or uM2-4 (RL-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
uM2-3 (RL+) - A57-5 (RL+) Always Below 1 Ω
uM2-3 (RL+) or A57-5 (RL+) - Body ground Always 10 kΩ or higher
uM2-4 (RL-) - A57-4 (RL-) Always Below 1 Ω
uM2-4 (RL-) or A57-4 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK REAR SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK REAR SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)
a.

Remove the component with the rear speed sensor rotor LH.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for 4WD/AWD)>REMOVAL


b.

Check the rear speed sensor rotor LH.

OK:

The rear speed sensor rotor LH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor rotor LH, clean the rear speed sensor rotor LH.

·

Do not use parts cleaner when cleaning the rear speed sensor rotor LH.

·

If the rear speed sensor rotor LH is damaged, replace the rear speed sensor rotor LH with a new one.



HINT:

The rear speed sensor rotor LH is incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor rotor LH needs to be replaced, replace it together with the rear axle hub and bearing assembly LH.



Result:
Result Proceed to
OK A
NG (The rear speed sensor rotor LH is damaged.) B
NG (There is foreign matter on the rear speed sensor rotor LH.) C



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

C

CLEAN REAR SPEED SENSOR ROTOR LH

8.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor LH
*a Correct
*b Incorrect
*c No clearance


Check the rear speed sensor LH installation.

OK:

There is no clearance between the rear speed sensor LH and the rear axle hub and bearing assembly LH.


HINT:

Because the rear axle hub and bearing assembly LH cannot be disassembled, if the rear speed sensor LH needs replacement, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (RL WHEEL SPEED)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

9.READ VALUE USING GTS (RL WHEEL SPEED)
a.

Perform a road test.


b.

Check the rear speed sensor LH output value.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RL Wheel Speed
50003 435 16
OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

10.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
10.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
a.
C425604C09
0.813,0.74 1.219,1.021 0.406,0.281 2.354,0.729 2.76,1.01 0.406,0.281 2.948,2.573 2.667,2 true 0.667,2.573 0.917,1.802 true 1.427,2.552 1.156,1.781 true 2.146,2.563 2.427,2 true 0.948,0.792 1.271,1.052 0.323,0.26 10 false u4 2.427,0.792 2.75,1.052 0.323,0.26 10 false uM2 1.271,0.771 1.594,1.031 0.323,0.26 10 false *b 2.833,0.729 3.156,0.99 0.323,0.26 10 false *c 0.135,0.135 0.458,0.396 0.323,0.26 10 false *a 1.396,2.594 1.719,2.854 0.323,0.26 10 false + 2.052,2.615 2.375,2.875 0.323,0.26 10 false RL+ 0.615,2.573 0.938,2.833 0.323,0.26 10 false - 2.865,2.615 3.188,2.875 0.323,0.26 10 false RL-
*a Front view of skid control sensor wire LH (No. 2 parking brake wire assembly)
*b to Sensor Side Connector
*c to Vehicle Side Connector


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the u4 and uM2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
u4-2 (+) - uM2-3 (RL+) Always Below 1 Ω
u4-2 (+) or uM2-3 (RL+) - Body ground and other terminals Always 10 kΩ or higher
u4-1 (-) - uM2-4 (RL-) Always Below 1 Ω
u4-1 (-) or uM2-4 (RL-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
uM2-3 (RL+) - A57-5 (RL+) Always Below 1 Ω
uM2-3 (RL+) or A57-5 (RL+) - Body ground Always 10 kΩ or higher
uM2-4 (RL-) - A57-4 (RL-) Always Below 1 Ω
uM2-4 (RL-) or A57-4 (RL-) - Body ground Always 10 kΩ or higher


HINT:

The rear speed sensor LH and rear speed sensor rotor LH are incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor LH and rear speed sensor rotor LH need to be replaced, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR