Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C051212  Right Rear Wheel Speed Sensor Circuit Short to Battery  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the No. 2 skid control ECU (brake actuator assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the No. 2 skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and No. 2 skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C422569E04
1.854,1.188 1.854,0.667 1.854,0.667 1.698,0.667 false 5.073,0.969 4.729,0.969 false 0.458,0.094 1.625,0.375 1.167,0.281 12 false for 2WD: 3.615,0.094 4.781,0.302 1.167,0.208 12 false for 4WD/AWD: 0.781,0.552 1.854,0.75 1.073,0.198 10 false Speed Sensor 1.25,2.469 2.667,2.719 1.417,0.25 10 false Speed Sensor Rotor 4.833,3.458 5.448,3.708 0.615,0.25 10 false 1.4 V 4.833,3.823 5.448,4.021 0.615,0.198 10 false 0.7 V 3.729,4.313 4.646,4.646 0.917,0.333 10 false High speed 2.792,4.313 3.604,4.646 0.813,0.333 10 false Low speed 4.583,2.5 6,2.75 1.417,0.25 10 false Speed Sensor Rotor 3.448,0.854 4.802,1.073 1.354,0.219 10 false Skid Control Sensor

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C051212 Right Rear Wheel Speed Sensor Circuit Short to Battery The speed sensor short signal is ON continuously for 0.5 seconds or more.
·

Rear skid control sensor RH*1

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)*2

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

*1: for 4WD/AWD

*2: for 2WD


WIRING DIAGRAM

for 4WD/AWD
C427731E09
0.406,2.281 1.531,2.688 1.125,0.406 10 false Rear Skid Control Sensor RH 1.844,2.281 4.052,2.667 2.208,0.385 10 false Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly) 5.188,3.094 7.104,3.729 1.917,0.635 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.781,1.25 6.281,1.49 0.5,0.24 10 false RR+ 2.792,1.125 3.24,1.385 0.448,0.26 10 false RR+ 1.365,1.125 1.781,1.365 0.417,0.24 10 false + 2,1.125 2.49,1.375 0.49,0.25 10 false + 1.375,1.813 1.771,2.052 0.396,0.24 10 false - 2,1.813 2.479,1.99 0.479,0.177 10 false - 2.781,1.813 3.24,2 0.458,0.188 10 false RR- 5.781,1.938 6.281,2.146 0.5,0.208 10 false RR- 1.656,1.115 2.208,1.354 0.552,0.24 10 false u3 1.656,1.813 1.99,2.063 0.333,0.25 10 false u3 3.198,1.125 3.688,1.344 0.49,0.219 10 false uM1 3.188,1.813 3.604,2.115 0.417,0.302 10 false uM1 1.698,0.906 2,1.135 0.302,0.229 10 false 1 5.188,2.906 5.688,3.104 0.5,0.198 10 false A57 1.688,1.594 1.99,1.823 0.302,0.229 10 false 2 3.292,0.917 3.594,1.146 0.302,0.229 10 false 3 3.302,1.615 3.604,1.844 0.302,0.229 10 false 4 5.542,1.021 5.833,1.26 0.292,0.24 10 false 20 5.531,1.698 5.885,1.948 0.354,0.25 10 false 19 1.531,3.313 2.677,3.542 1.146,0.229 10 false *: Shielded 4.646,2.167 4.948,2.396 0.302,0.229 10 false *

for 2WD
C427731E26
0.219,2.281 1.656,2.865 1.438,0.583 10 false Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH) 1.844,2.281 4.052,2.729 2.208,0.448 10 false Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly) 5.177,3.115 7.083,3.75 1.906,0.635 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.781,1.25 6.281,1.49 0.5,0.24 10 false RR+ 2.792,1.125 3.24,1.385 0.448,0.26 10 false RR+ 1.385,1.125 1.802,1.365 0.417,0.24 10 false + 2,1.125 2.49,1.375 0.49,0.25 10 false + 1.396,1.823 1.792,2.063 0.396,0.24 10 false - 2,1.823 2.479,2 0.479,0.177 10 false - 2.802,1.823 3.26,2.01 0.458,0.188 10 false RR- 5.792,1.927 6.292,2.135 0.5,0.208 10 false RR- 1.656,1.115 2.208,1.354 0.552,0.24 10 false u3 1.656,1.823 1.99,2.073 0.333,0.25 10 false u3 3.198,1.125 3.688,1.344 0.49,0.219 10 false uM1 3.198,1.813 3.615,2.115 0.417,0.302 10 false uM1 1.688,1.604 1.99,1.833 0.302,0.229 10 false 1 5.177,2.938 5.677,3.135 0.5,0.198 10 false A57 1.698,0.917 2,1.146 0.302,0.229 10 false 2 3.292,0.917 3.594,1.146 0.302,0.229 10 false 3 3.292,1.604 3.594,1.833 0.302,0.229 10 false 4 5.531,1.021 5.823,1.26 0.292,0.24 10 false 20 5.521,1.698 5.875,1.948 0.354,0.25 10 false 19 1.583,3.292 2.813,3.563 1.229,0.271 10 false *: Shielded 4.646,2.167 5.063,2.469 0.417,0.302 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for 4WD/AWD. A
for 2WD. B



A

2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

B

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.
C419796C29
1.458,0.167 1.875,0.417 0.417,0.25 1.854,1.229 2.188,1.729 true 1.552,1.229 1.219,1.729 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.594,0.208 1.917,0.396 0.323,0.188 10 false u3 1.146,1.75 1.563,2 0.417,0.25 10 false + 2.208,1.74 2.625,2 0.417,0.26 10 false -
*a Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
(to Rear Skid Control Sensor RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the u3 rear skid control sensor RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
u3-1 (+) - u3-2 (-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.
C425605C01
1.49,0.406 1.885,0.667 0.396,0.26 0.969,2.927 1.438,2.521 true 2.531,2.917 1.99,2.51 true 1.563,0.448 1.969,0.729 0.406,0.281 10 false uM1 0.188,0.104 0.594,0.385 0.406,0.281 10 false *a 2.542,2.938 2.948,3.219 0.406,0.281 10 false RR+ 0.688,2.948 1.094,3.229 0.406,0.281 10 false RR-
*a Front view of wire harness connector
(to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the uM1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
uM1-3 (RR+) - uM1-4 (RR-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.
C425605C02
1.49,0.406 1.885,0.667 0.396,0.26 0.969,2.927 1.438,2.521 true 1.563,0.448 1.969,0.729 0.406,0.281 10 false uM1 0.188,0.104 0.594,0.385 0.406,0.281 10 false *a 0.688,2.948 1.094,3.229 0.406,0.281 10 false RR-
*a Front view of wire harness connector
(to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
uM1-4 (RR-) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
uM1-3 (RR+) or A57-20 (RR+) - uM1-4 (RR-) or A57-19 (RR-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.
C419796C60
1.458,0.167 1.875,0.417 0.417,0.25 1.854,1.229 2.188,1.729 true 1.552,1.229 1.219,1.729 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.594,0.208 1.917,0.396 0.323,0.188 10 false u3 2.188,1.75 2.604,2 0.417,0.25 10 false + 1.146,1.74 1.563,2 0.417,0.26 10 false -
*a Front view of skid control sensor wire RH (No. 1 parking brake wire assembly)
(to Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the u3 rear speed sensor RH (rear axle hub and bearing assembly RH) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
u3-2 (+) - u3-1 (-) Ignition switch ON 11 to 14 V


HINT:

The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.
C425605C01
1.49,0.406 1.885,0.667 0.396,0.26 0.969,2.927 1.438,2.521 true 2.531,2.917 1.99,2.51 true 1.563,0.448 1.969,0.729 0.406,0.281 10 false uM1 0.188,0.104 0.594,0.385 0.406,0.281 10 false *a 2.542,2.938 2.948,3.219 0.406,0.281 10 false RR+ 0.688,2.948 1.094,3.229 0.406,0.281 10 false RR-
*a Front view of wire harness connector
(to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the uM1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
uM1-3 (RR+) - uM1-4 (RR-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
8.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.
C425605C02
1.49,0.406 1.885,0.667 0.396,0.26 0.969,2.927 1.438,2.521 true 1.563,0.448 1.969,0.729 0.406,0.281 10 false uM1 0.188,0.104 0.594,0.385 0.406,0.281 10 false *a 0.688,2.948 1.094,3.229 0.406,0.281 10 false RR-
*a Front view of wire harness connector
(to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
uM1-4 (RR-) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
uM1-3 (RR+) or A57-20 (RR+) - uM1-4 (RR-) or A57-19 (RR-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR