Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C14D71C  Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range  


DESCRIPTION

The yaw rate sensor has a built-in acceleration sensor.

This DTC is stored when the No. 2 skid control ECU (brake actuator assembly) receives a sensor supply voltage malfunction signal from the yaw rate sensor.

This DTC may be stored due to an intermittent low power source voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C14D71C Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range When the +BS terminal voltage is from 9.5 to 17.4 V at a vehicle speed exceeding 3 km/h (2 mph), an acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

Wire harness and connector

·

Acceleration sensor (yaw rate sensor)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

WIRING DIAGRAM

C423255E03
5.188,4.135 7.083,4.656 1.896,0.521 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.177,3.958 5.583,4.167 0.406,0.208 10 false A57 5.771,0.344 6.177,0.552 0.406,0.208 10 false 27 5.771,0.979 6.177,1.188 0.406,0.208 10 false 43 6.073,0.542 6.531,0.75 0.458,0.208 10 false CANH 6.063,1.188 6.521,1.396 0.458,0.208 10 false CANL 0.781,1.208 1.24,1.417 0.458,0.208 10 false CANL 1.302,0.979 1.76,1.188 0.458,0.208 10 false 2 0.76,0.531 1.219,0.74 0.458,0.208 10 false CANH 1.302,0.333 1.76,0.542 0.458,0.208 10 false 3 1,2.167 1.458,2.375 0.458,0.208 10 false IG 1.313,2.052 1.771,2.26 0.458,0.208 10 false 4 2.021,2.344 3.104,2.573 1.083,0.229 10 false ECU-IG1 NO. 2 2.24,2.01 2.698,2.219 0.458,0.208 10 false 2 2.604,2.01 3.063,2.219 0.458,0.208 10 false 1 3.948,2.156 5.125,2.385 1.177,0.229 10 false from IG Circuit 0.865,3.177 1.323,3.385 0.458,0.208 10 false GND 1.302,3.052 1.49,3.26 0.188,0.208 10 false 1 0.271,4.052 0.729,4.26 0.458,0.208 10 false M1 0.271,4.229 1.688,4.49 1.417,0.26 10 false Yaw Rate Sensor 3.146,3.646 4.885,3.948 1.74,0.302 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing or reinstalling the yaw rate sensor, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG TERMINAL)
a.
C156491C85
0.323,1.156 0.677,1.396 0.354,0.24 1.771,2.302 1.948,2.917 true 0.219,0.24 0.531,0.438 0.313,0.198 10 false *a 0.406,1.198 0.719,1.396 0.313,0.198 10 false M1 1.906,2.948 2.219,3.146 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Yaw Rate Sensor)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the M1 yaw rate sensor connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M1-4 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M1-1 (GND) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Reconnect the M1 yaw rate sensor connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C14D71C is not output. A
DTC C14D71C is output. B



A

B