Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C12D112  Left Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery  C12D114  Left Rear Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open  C12D118  Left Rear Wheel ABS Hold Solenoid Control Circuit Current Below Threshold  C12D119  Left Rear Wheel ABS Hold Solenoid Control Circuit Current Above Threshold  C12D11D  Left Rear Wheel ABS Hold Solenoid Control Circuit Current Out of Range  C12DC12  Left Rear Wheel ABS Release Solenoid Control Circuit Short to Battery  C12DC14  Left Rear Wheel ABS Release Solenoid Control Circuit Short to Ground or Open  


DESCRIPTION

The solenoid relay and solenoid valves are built into the brake actuator assembly.

The rear solenoid valve LH controls the brake fluid pressure of the rear wheel cylinder LH of the vehicle.

When these DTCs are stored, the fail-safe function operates and the solenoid relay is turned off to prevent the solenoid valves from operating.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C12D112 Left Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery An excessive current is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12D114 Left Rear Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open Insufficient current is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12D118 Left Rear Wheel ABS Hold Solenoid Control Circuit Current Below Threshold An open is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12D119 Left Rear Wheel ABS Hold Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12D11D Left Rear Wheel ABS Hold Solenoid Control Circuit Current Out of Range Current leakage is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12DC12 Left Rear Wheel ABS Release Solenoid Control Circuit Short to Battery Any of the following is detected:
·

Overcurrent is detected in the solenoid for 0.05 seconds or more.

·

Overheat in the solenoid is detected for 0.05 seconds or more.

·

When the solenoid is OFF, a current leak in the solenoid circuit is detected for 0.05 seconds or more.


No. 2 skid control ECU (brake actuator assembly) Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12DC14 Left Rear Wheel ABS Release Solenoid Control Circuit Short to Ground or Open Any of the following is detected:
·

When the solenoid is not being operated, an open in the solenoid circuit or short to ground is detected for 0.05 seconds or more.

·

When the solenoid is being operated, an open in the solenoid circuit is detected for 0.05 seconds or more.

·

An open in the solenoid ground circuit is detected for 0.05 seconds or more.


No. 2 skid control ECU (brake actuator assembly) Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY

NEXT

END